Tata Memorial Centre - Maharashtra

39933701 tender for area development in backside of kitchen and laundry at actrec; 1 excavation depth up to 1.5mexcavation in foundation / trenches / pits drains / roads etc. in all soils upto a required depth not exceeding 1.5 mtrs. including shoring and dewatering if necessary and refilling around foundation plinth and drain line with selected excavation earth in layers not exceeding250mm consolidating and disposing surplus earth out of hospital premises complete all as directed by the engineer in charge. 2 pcc 1:2:4 rmc m15using 20mm max. size aggregate. plain cement concrete 1:2:4 using graced stone aggregate of 20mm max. size including consolidation using vibrator & needle if required finishing, curing, form work shuttering, centering etc. complete all as per specification and in quantity as & when required by the engineer in charge, 3 rcc m20rmc1:1.5:3 ( 1 cement : 1.5 coarse sand ( zone iii ) derived from naturalsources : 3 graded stone aggregate 20 mm nominal size derived from natural sources ) providing and laying in position specified grade of reinforced cementconcrete, excluding the cost of centering, shuttering, finishing andreinforcement all work up to plinth level 4 form work centering and shuttering including strutting, propping etc. and removalof form for in quantity as & when required by the engineer in charge, 5 steel reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding all complete up to plinth level. 6 providing and filling in position bitumen covering of expansion joint mix filler of proportion 80 kg. ofhot bitumen, 1 kg. of cement and 0.25 cubic metre of coarse sand forexpansion joints. complete all as directed by the engineer in charge. ( the compacted thickness of stone soling laid shall be measured for payment. ) 7 225mm thick soling: providing & laying rubble stone soling using spotless stones below floors roads / pavements etc. mechanically / manually consolidated thickness 225mm with stones vertically handset interstices packed with smaller stone chips, binding with murrum & sprinkling water for proper consolidating and finishing to required levels in quantities as and when required etc. complete all as directed by the engineer in charge. ( the compacted thickness of stone soling laid shall be measured for payment. ) 8 brick work: brick work at all floor level with cement mortar 1:4 using well burnt locally available bricks of approved quality including scaffolding, raking out joints above ground level simultaneous and as directed by engineer in charge. in foundation & plinth drain walls chambers & superstructure of all floor levels. 9 plaster 20mm thick for wall: cement plastering for internal wall and ceiling with cement mortar 1:4 finished smooth with neeru over brick walls of concrete surfaces including hacking the concrete surfaces at all floors and levels in quantities as required at site including scaffolding curing, etc. complete all as directed by engineer in charge. 10 chamber: inside size 90x80 cm and 45 cm deep including c.i. cover with frame ( light duty ) 455x610 mm internaldimensions, total weight of cover and frame to be nostless than 38 kg ( weight of cover 23 kg and weightof frame 15 kg ) :with common burnt clay f.p.s. ( nosn modular ) bricks of class designation 7.5 ( work includes removing old fixtures ) complete all as directed by engineer in charge. 11 455x610 mm rectangular rcc coverthe weight of the cover to be not less than 23 kg : providing and fixing rcc chamber cover with frame of size weight and numbers as specified including cost of necessary 1:2:4 cement concrete and 1:4 cement mortar for fixing, painting the frame and cover with two coats of approved paintof approved shade etc, complete all as directed by the engineer in charge 12 300 mm rcc spun pipe: providing fixing lowering and laying rcc spun pipes cement pipe or rcc hume pipe ( class np2 of isi ) with necessary collars jointing with hemp yarn and cement1:1 including embedding in walls beams floors etc. caulking the joints finishing alighting to proper level etc. complete as specified and directed. 13 providing and fixing frp gratings including ms framing of angel section of 50x50x5 ( thickness 25mm, width 400mm and suitable length ) in position over the rain water drains as directed by eic. 14 providing and fixing ms gratings including ms framing of angel section of 50x50x5 ( thickness 25mm, width 400mm and suitable length ) in position over the rain water drains as directed by eic. 15 structural steel work: at all levels including supplying cutting fabricating welding or blotting erecting and fixing in position including painting with a primary coat of approved steel primer, including cost of materials labour with chasing in wall or embedding in floor and making good the same by filling 1:2:4 cement concrete and plastering if necessary all as specified and directed by engineer in charge. 16 providing and fixing g.i. chain link fabric fencing of required width in mesh size 50x50 mm including strengthening with 2 mm dia wire ornuts, bolts and washers as required complete as per the direction of engineer in charge. made of g.i. wire of dia. 4 mm, pvc coated to achieve outer dia not less than 5 mm in required colour and shade all as specified and directed by engineer in charge. 17 providingandfixingprecoatedgalvanisedironprofilesheets ( size, shape and pitch of corrugation as approved by engineer in charge ) 0.50 mm ( + 0.05 % ) total coated thickness with zinc coating 120 grams per sqm as per is: 277, in 240 mpa steel grade, 5 7 microns epoxy primer on both side ofthe sheet and polyester top coat 15 18microns. sheet shouldhaveprotectiveguardfilmof25micronsminimumtoavoid scratches during transportation and should be supplied in single length up to 12 metre or as desired by engineering charge. the sheet shall be fixed using self drilling / self tapping screws of size ( 5.5x 55 mm ) with epdmseal, completeupto any pitch in horizontal / verticalor curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 18 using acrylic emulsion paints ( plastic paints ) providing & applying one / two coatsof primer & thereafter two coats of paint as mentioned below of approved make first quality asian paints to the required colour scheme and as per manufacturers instructions / specificationsto the walls, beams, columns, ceilings, partitions doors etc. including thoroughly scrapping the existing surface with sand papers, removing old paint, filling up crevices and levelling with waterproofputty / plaster of paris of necessary to obtain smooth surface etc. complete job including removal of stains, painting spots on floors, aluminium window frame & glassetc asto the entire satisfaction of engineer in charge 19 for metal surface like staircase, channels and doors for the enamel paint providing & applying one / two coatsof primer & thereafter two coats of paint as mentioned below of approved make first quality asian paints to the required colour scheme and as per manufacturers instructions / specificationsto the walls, beams, columns, ceilings, partitions doors etc. including thoroughly scrapping the existing surface with sand papers, removing old paint, filling up crevices and levelling with waterproofputty / plaster of paris of necessary to obtain smooth surface etc. complete job including removal of stains, painting spots on floors, aluminium window frame & glassetc asto the entire satisfaction of engineer in charge 20 paver block : providing & laying 60mm thick factory made cement concrete interlocking paver block heavy duty of m 30 grade made by block making machine with strong vibratory compaction and approved size and design / shape laid in required colour and pattern over and including 50mm thick compacted bed of course sand filling the joints with coarse sand etc., a;; complete as per the direction of engineer in charge. 21 curb stone: stone providing fixing curb stone of 300x300 section and 200 in width block heavy duty of m 30 grade made by block making machine with strong vibratory compaction and approved size and design / shape laid in required colour and pattern over and including 50mm thick compacted bed of course sand filling the joints with coarse sand etc., a;; complete as per the direction of engineer in charge. 22 light colour e.w.c.: providing and fixing white vitreous china pedestaltype water closet ( european type w.c. pan ) with seatand lid, level white p.v.c. flushing cistern with capacity as mentioned below, including flush pipe, with manually controlled device ( handle lever ) , conforming to is : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required. it should include p or s trap as per approved make with left or right vent in position including fixing it on chair bracket or wall bracket. with necessary c.p. brass screws & plugs etc. make : any make 23 p or s trap: providing & fixing heavy quality lead p or s trap with union cleaning eye at bottom white solder joints etc. complete as and when required and as directed by the engineer in charge. 24 filling murrum bought from outside: filling under floors with available earth / murrum / debris or brought from outside sources spreading in 200mm thick layer, watering consolidating to 150mm thickness and finished to desired levels etc. complete. ( 17sqm x 0.3m depth ) ( disposing / taking away the debris outside the premises & diposing as per the guidelines of statutory authorised....

Hydro Electirc Project - Maharashtra

39681377 electrical components for rehabilitation of jayakawadi dam, paithan dist. aurangabad 2 sub estimate a : supply, erection, testing & commissioning of transformer & panel at jayakwadi dam 3 item no 1 :supplying, installing, testing & commissioning of 3 phase, 11/0.433 kv, 50 hz., 100 kva, oil immersed and naturally cooled outdoor type, copper wound transformer, delta/star connected with additional neutral brought out on load side, temperature rise should not exceed 40oc by thermometer in oil and 45oc by the resistance in winding at full load rating, with hv tapping (with off load tap changer) off load +5 to 10 in steps of 2.5%, with standard accessories complete with test certificate with losses below 475 watts at 50% load, 1650watts at 100% load as per is:1180 2014 energy efficiency level ii, with necessary permissions of electrical inspector, as per specification no ss tr. 4 item no 2 :supplying & erecting end pole d. p. structure for 11/0.415 kv, 100 kva transformer with r.s.j. pole 2 nos. of size 100 x 116 mm x 11 mtr. long with suitable distribution box of c.r.c.a. sheet 16 swg with 4 pole mccb 200 amps as incomer & 6 nos.100 amps kitkat/mccb for outgoingcircuits. transformer d.p. structure includes the a. b. switch 200 amps, d.o. fuse set & l.a. set. 2 nos. top channel of size 100 mm x 50 mm for erection of a.b. switch & 2 nos. base channel of size 100 mm x 50 x mm for erecting transformer. channel of size 75 x40 mm for erecting d.o. fuse set, l.a., a.b. switch handle etc. angle of size 50 x 50 x6 mm for erecting distribution box , transformer belt etc.as per drawing (min. 124 kg. iron work ) with necessary clamps, nut bolts. vee cross arm, top clip, insulators etc. complete with caution board & barbed wire. d.p. structure shall be erected inc.c. foundation complete. 5 item no3 :providing pipe type earthing with 40mm. dia. g.l. pipe or 20 mm dia. g.l. rod complete with all materials as per specification no. eaep 6 item no 4: supplying, erecting & terminating xlpe armoured cable 3½core 240 sq. mm. aluminium conductor with continuous 12.97 sq.mm. (8 swg) g.i. earth wire complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. cb lt/al 7 item no 5: supplying and erecting four pole metal clad on load change over switch 415 v, 400a erected on angle iron / gi frame complete. 8 item no 6:providing & erecting 3 pole mccb of 315/400a, 415v capacity with short circuit rating 36 ka (ics=100% of icu), adjustable thermal (overload) setting and fixed magnetic setting with provided leads, provision for installation of shunt/ uv/ trip alarm contact and mccb should have phase barriers both sides, in provided enclosure on iron /gi frame as per specification no. sw swr/mccb 9 item no 7:supplying and erecting lt ct multifunction dlms compliance energy meter of accuracy of class 0.5 , 3x240v,50 hz with optical & rs 232 port, backlit lcd, measures & displays trivector energy, load survey, tod, tamper detection & logging, power on /off events, instantaneous parameters of rating 1/5 a with display in absence of power complete with zero adjustment & test certificate from manufacturer erected on provided m.s. box and connected to cts 10 item no 8:supplying and erecting lt current transformer with bar primary 50/5 to 1000/5 ratio with 15 va burden erected in provided crca box duly secured with insulating materialsconnected to the meter with test certificates. 11 item no 9: supplying, erecting & terminating xlpe armoured cable 1100 v. 3½ core 185 sq. mm. aluminium conductor with continuous 12.97 sq. mm. (8 swg) g.i. earth wire complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipeas per specification no. cb lt/all 12 item no 10 :providing & erecting 3 pole mccb of 200a,415v capacity with short circuit rating 25 ka (ics=100% of icu) adjustable thermal (overload) setting and fixed magnetic setting with provided leads,provision for installation of shunt/ uv/ trip alarm contact and mccb should have phase barriers both sides, in provided enclosureon iron /gi frame as per specification no. sw wr/mccb 13 item no 11 :providing & erecting 3 pole mccb upto 100a, 415v, with short circuit rating 25 ka (ics=100% of icu ),adjustable thermal (overload) setting and fixed magnetic setting with provided leads, provision for installation of shunt/ uv/ trip alarm contact and mccb should have phase barriers both sides, in provided enclosureon iron /gi frame as per specification no. sw wr/mccb 14 item no 12 :supplying and erecting bus bar chamber triple pole with neutral with four aluminium bars, 500v 400a complete as per specification no.cp bb 15 item no 13 :supplying & erecting led type indicating pilot lamp with led colours red / yellow / green, 230 / 250v on provided box / panel with necessary material, wiring & connections etc. 16 item no 14 :supplying and erecting metal work in crca sheet with fabrication of boxes, panel boards, etc. including cutting, bending, drilling, welding, riveting, treated with anti rust treatment and duly powder coated or painted with one coat of red lead paint and 2 coats of enamel paint complete. 17 item no 15 :making trench of suitable width and depth in soft soil for laying provided lt cable of 16 sq. mm & above and covered with half round hume pipe complete as per specification no. cw exnctr 18 item no 16 :supplying & erecting mains with 4x25 sq.mm f.r copper pcc insulated wire laid in provided conduit/trunking/inside pole/bus bars or any other places as per specification no: wgma/bw 19 item no 17 :supplying & erecting mains with 4x50 sq.mm fr copper pcc insulated wire laid in provided conduit/trunking/inside pole/bus bars or any other places as per specification no: wgma/bw 20 item no 18: supplying and erecting terminal spreaders for use on mccb incoming and outgoing terminals for 3 pole upto 100a mccb complete. (set of 6). 21 item no 19: supplying and erecting terminal spreaders for use on mccb incoming and outgoing terminals for 3 pole upto 250a mccb complete. (set of 6) 22 item no 20:supplying and erecting terminal spreaders for use on mccb incoming and outgoing terminals for 3 pole 300a 400amccb complete. (set of 6) 23 item no 21:supplying and spreading stone metal 25 mm size for 100 mm depth above the ground level complete. 24 item no 22 :supplying and erecting g.i. stay set for poles, includingloop insulators at inaccessible height complete with anchor plate 300 x 300 x 6 mm., straining screws, g.i. stay wire 7/10 swg, g.l. stay rod 20 mm x 1.8 m length andpole clamps duly erected in provided cement concrete foundation. 25 item no 23: dismantling existing pole mounted distribution transformer safely without any damages. 26 item no 24: dismantling existing do / ab switch set complete from d.p. structure in an approved manner. 27 item no 25: dismantling the existing pole above 6 m height with brackets, clamps, insulators, stay from the cement concrete foundation and making the site clear by refilling the pits with excavated materials and bringing it to the ground level. 28 item no 26: dismantling existing lightning arrestor set, insulator complete from dp structure in an approved manner. 29 item no 27: dismantling the existing cables of all types & size above 50 sq. mm. 30 item no 28:dismantling the existing switchgears, db, and bus bar of any size complete with/ without board or angle iron frame complete. 31 supply, erection , testing & comissioning of cables &control panel at inspection gallary at jayakwadi dam 32 item no 29:making trench of suitable width and depth in soft soil for laying provided lt cable of 16 sq. mm & above and covered with half round hume pipe complete as per specification no. cw exnctr 33 item no 30: supplying, erecting & terminating xlpe armoured cable 3½ core 70 sq. mm. aluminium conductor with continuous 8.35 sq. mm. (10 swg) g.i. earth wire complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as perspecification no. cb lt/al 34 item no 31:supplying and erecting four pole metal clad on load change over switch 415v, 200a erected on angle iron /gi frame approved make complete. 35 item no 32 : providing & erecting 3 pole mccb of 200a,415v capacity with short circuit rating 25 ka (ics=100% of icu) adjustable thermal (overload) setting and fixed magnetic setting with provided leads, provision for installation of shunt/ uv/ trip alarm contact and mccb should have phase barriers both sides, in provided enclosure on iron /gi frame as per specification no. sw swr/mccb 36 item no 33: providing & erecting 3 pole mccb upto 100a, 415v, with short circuit rating 25 ka (ics=100% of icu ),adjustable thermal (overload) setting and fixed magnetic setting with provided leads, provision for installation of shunt/ uv/ trip alarm contact and mccb should have phase barriers both sides, in provided enclosure on iron /gi frame as per specification no. sw wr/mccb 37 item no 34:supplying and erecting of any size electrolyte aluminium patti or bar in bus bar chamber / in panel or any other purpose, 500 v with require capacity with 99.9% aluminium purity with fixing arrangement (like lug or bottle type lug) to both the end with high grade polyolefin insulation sleeve complete as per specification no. bcp bb 38 item no 35:supplying and erecting metal work in crca sheet with fabrication of boxes, panel boards, etc. including cutting, bending, drilling, welding, riveting, treated with anti rust treatment and duly powder coated or painted with one coat ofred lead paint and 2 coats of enamel paint complete. 39 item no 36: supplying, erecting & terminating xlpe armoured cable 4 core 10 sq. mm. aluminium conductor with continuous 5.48 sq. mm. (12 swg) g.i. earth wire complete erected with glands & lugs, on wall/ trusses/pole or laid in providedtrench/ pipe as per specification no. cb lt/al 40 item no 37 : supplying, erecting & terminating xlpe armoured cable 3½ core 25 sq. mm. aluminium conductor with continuous 5.48 sq. mm. (12 swg) g.i. earth wire complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. cb lt/al 41 item no 38 : supplying & erecting original 1.25 mm crca sheet metal enclosures with 30a, 3 pin plug & earth socket and 30 a 3 pin plug top with 30a triple pole mcb complete erected on angle iron/ gi frame 42 item no 39 :supplying and erecting led street light fitting suitable above 26w to 36w lamp, including lamp, with pf > 0.95 class ip 65 and above housing of pressure die cast aluminium alloy and heat sink extruded aluminium complete as per specification no fgodf/fls2. 43 item no 40 : supplying, erecting & marking spmcb 0.5a to 5a in provided distribution board as per specification no. sw swr/mcb 44 item no 41 :supplying & erecting frp box of size 150 x 125 x 100 mm, 2.7 mm thick complete on pole/wall as per specification no. cb sb 45 item no 42: supplying & erecting mains with 2x1.5 sq.mm f.r copper pcc insulated wire laid in provided conduit/trunking/inside pole/bus bars or any other places as per 46 item no 43:dismantling the existing cables of all types & size above 50 sq. mm. 47 item no 44: dismantling the existing cables of all types & size up to 10 sq. mm. 48 item no 45: dismantling the existing switchgears, db, and bus bar of any size complete with/ without board or angle iron frame complete. 49 item no 46: dismantling the existing underground cable without damaging it with glands, cable end box including refilling the trench up to ground level and making coils complete. 50 supply, erection, testing & commissioningof making electrical supply arrangement for the gate operationat jayakwadi dam 51 item no 47: supplying, erecting & terminating xlpe armoured cable 3½ core 70 sq. mm. aluminium conductor with continuous 8.35 sq. mm. (10 swg) g.i. earth wire complete erected with glands & lugs, on wall/ trusses/pole or laid in providedtrench/ pipe as per specification no. cb lt/al 52 item no 48: supplying, erecting & terminating xlpe armoured cable 3½ core 50 sq. mm. aluminium conductor with continuous 5.48 sq. mm. (12 swg) g.i. earth wire complete erected with glands & lugs, on wall/ trusses/pole or laid in providedtrench/ pipe as per specification no. cb lt/al 53 item no 49:supplying, erecting & terminating xple armoured cable 4 core 16 sq. mm. aluminium conductor with continuous 5.48 sq. mm. (12 swg) g.i. earth wire complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. cb lt/al 54 item no 50:providing & erecting 3 pole mccb upto 100a, 415v, with short circuit rating 25 ka (ics=100% of icu ),adjustable thermal (overload) setting and fixed magnetic setting with provided leads, provision for installation of shunt/ uv/ trip alarm contact and mccb should have phase barriers both sides, in provided enclosure on iron /gi frame as per specification no. sw wr/mccb 55 item no 51:supplying and erecting metal work in crca sheet with fabrication of boxes, panel boards, etc. including cutting, bending, drilling, welding, riveting, treated with anti rust treatment and duly powder coated or painted with one coat of red lead paint and 2 coats of enamel paint complete. 56 item no 52: supplying and erecting of any size electrolyte aluminium patti or bar in bus bar chamber / in panel or any other purpose, 500 v with require capacity with 99.9% aluminium purity with fixing arrangement (like lug or bottle type lug) to both the end with high grade polyolefin insulation sleeve complete as perspecification no. bcp bb 57 item no 53: supplying and erecting led flood light fitting of 90 100w, including lamp, with pf > 0.95, class ip 65 and above housing of pressure die cast aluminium alloy and heat sink extruded aluminium complete as per specification no fg df/fls 2 58 item no 54 :supplying and erecting led street light fitting suitable for above 40w to 48w lamp, including lamp, with pf > 0.95 class ip 65 and above housing of pressure die cast aluminium alloy and heat sink extruded aluminium complete as per specification no . fg odf/fls2 59 item no 55 : supplying & erecting frp box of size 150 x 125 x 100 mm, 2.7 mm thick complete on pole/wall as per specification no. cb sb 60 item no 56 : supplying, erecting & marking spmcb 0.5a to 5a in provided distribution board as per specification no. sw swr/mcb 61 item no 57 :supplying & erecting mains with 2x1.5 sq.mm f.r copper pcc insulated wire laid in provided conduit/trunking/inside pole/bus bars or any other places as per specification no: wgma/bw 62 item no 58 :supplying & erecting mains with 2x2.5 sq.mm f.r copper pcc insulated wire laid in provided conduit/trunking/inside pole/bus bars or any other places as per specification no: wgma/bw 63 item no 59 :supplying, erecting & terminating xlpe armoured cable 4 core 10 sq. mm. aluminium conductor with continuous 5.48 sq. mm. (12 swg) g.i. earth wire complete erected with glands & lugs, on wall/ trusses/pole or laid in providedtrench/ pipe as per specification no. cb lt/al 64 item no 60 :supplying, installing, testing and commissioning solar street light pole comprising of 12w led luminaire, 12.8v 30ah li battery, with 75wp solar panel, ms powder coated battery box weatherproof, mounted on 75/80 mm dia. bgrade gi pole of 6 mtr. height (5m above ground & 1m below ground), 12w led chip of luminaire should be in compliance to ies: lm 80 & performance parameters of luminaire shall be as per ies lm 79:2008 or is 16106 : 2012); along with brackets, foundation, earthing and necessaryaccessories complete as per mnre specification (with 5 years warrantee) 65 item no 61 :supplying, erecting & marking spmcb 6a to 32a, b series (for lighting) in provided distribution board as per specification no. sw swr/mcb 66 item no 62 : supplying, erecting and marking enclosure single pole and neutral distribution board (spndb) one pole for spmcb 1 no on iron/ gi frame as per specification no. swswr/mcbdb 67 item no 63: point wiring in pcc trunking (casing capping) with 1.5 sq.mm (2+1e) frlsh grade copper wire, flush type switch, earthing and required accessories as per specification no: wgpw/ sw 68 item no 64: wiring for plug on board with switch socket, copper wiring and earthing as per specification no: wg pw/sw 69 item no 65: supplying & erecting mains with 2x2.5 sq.mm. and earth wire 1.5 sq.mm frlsh pcc copper wire in hms pcc conduitmin. 20mm dia. as per specification no: wg ma/pc. 70 item no 66: supplying, erecting & terminating xlpe armoured cable 2 core 2.5 sq. mm. copper conductor continuous 5.48 sq.mm. (12 swg) g.i. earth wire complete erected with glands& lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. cb lt/cu 71 item no 67 : supplying and erecting regular/ standard model ceiling fan of 1400mm. sweep complete erected in position as per specification no. fg fn/cf 72 item no 68 : supplying and erecting cabin fan of a.c. 230 v. 50 cycles 250 mm. /300 mm. sweep complete with necessary brackets for fixing cabin fans, wire etc. 73 item no 69 :supplying and erecting exhaust fan medium duty 230 v a.c. 50 cycles 225 mm. 1400 rpm with condenser complete erected in position with necessary materials. fan motor with moisture proof treatment and =e‘ class insulation. 74 item no 70 :supplying & erecting led 18w tube light fitting (4 feet) with polycarbonate housing, heat sink, integrated hf electronic driver complete. 75 item no 71:supplying & erecting 18w, 230v integral type led lamp suitable for b 22/e 27 base. 76 item no 72 :providing & erecting hot dipped galvanized cover suitable for perforated type cable tray manufactured from 18 swg (1.2 mm thick) gi sheet of 500 mm width & 20 mm height complete with necessary hardware in approved manner. 77 item no73 :providing & erecting hot dipped galvanized perforated type cable tray manufactured from 16 swg (1.6 mm thick) gi sheet of 500 mm width & 75 mm height complete with necessary coupler plates & hardware in approved manner. 78 item no74 : providing floor mounting stand for keeping 4 nos. of fire buckets 1500mm in length, 900mm in height frame made out of 30x30x4 mm angle iron with cross supports for legs, welded with 4 hooks and duly painted with one coat of red lead and two coats of silver paint complete. 79 item no75 : providing round bottom fire bucket of 9 litres capacity as per is :2546 made out of 24 gauge g.i. sheet with extra handle at bottom duly painted white inside and red outside with fire mark, on provided stand/ wall hook complete. 80 item no76 : providing pair of duly tested rubber hand gloves as per is :47705 suitable for working upto 22 kv supply complete. 81 item no77:supplying standard first aid box with necessary antiseptic cream, medicine for use on wounds due burn, crepe bandage, gauge bandage, medicated ready to use bandage (band aid) adhesive tape for medicinal use, scissors, anti septic solution, etc. (all above contents shall be of standard makes) 82 item no78 :supplying shock proof leather safety shoes of electrical grade of standard size as is :11226, 14544 duly tested, with necessary test certificate from manufacturer. 83 item no79 :supplying and erecting d.c.p. type fire extinguisher 9 kg capacity cartridge type with gun metal cap 150 gram co2 gas cartridge, powder and brackets conforming to is 2171 1985 and complete erected with necessary clamps made from 50x6 mm m.s. flat with nuts & bolts grouted in wall complete. 84 item no 80: supplying and erecting abc powder type fire extinguisher as per is : 13849 /15683 of 6 kg capacity with necessary clamp for erection on wall. 85 item no 81: supplying and fixing pcc synthetic elastomer electrically insulating mat with class b insulation conforming to is: 15652 – 2006 & cpri tested having 2.5 mm thickness upto 11 kv 86 item no 82: supplying and erecting iron, sheet metal work consisting of crca sheets, various sections of iron, plates, chequered plates, rods, bars, ms pipes, etc. for panel board or any other purpose with bending, cutting, drilling and welding complete erected at the position with necessary materials duly painted with one coat of red oxide and two coats of enamel paint to match the switchgears or as per directions by the authority. 87 item no 83: sitc of 415 volts, 3 phase, 50 hz siren of 8 km range, horizontal double mounting type of 5 h.p. 2800 rpm on c.c. foundation complete as per specification no. srn as/sm 88 item no 84: supplying and erecting flat flexible 3 core 4 sq mm pcc sheathed submersible type copper cable suitably clamped at fixed intervals with column pipe assembly complete. 89 item no 85:early streamer lightening arrestor: sttc of advanced streamer emmision (ese) type of lightening arrestor of covering a radious of 125 meter, when mounted at a height of 5 meter above terrace floor leve, having triggering time 63 micron second, totally atonomous device, designed to work on positively as well as negatively charged cloud condition, internal triggering circuitry & electronics should contain ambient electric field sensor, charge accumulator, command & hv amplifier, transformer & triggering release. it is designed as per nfc17 32 & iec 60 1:1989. ese ternimal should be tested by cpri for the impulse current of 40ka (8/20 micro sec) with 5 positive & 5 negative impulse with folllowing specifications of capacity 200 ka (3/35 micro second ), capacity against wind speed 40m/s, dimension 39cm, lower diameter of ese should be 30.5 cm, weight=4 kg, the ese lightening arrestor should be should be tested in msme devlopment institute, along with of 6 digit transient event counter with display digit from 0 to 999999 for a minimum count impulse greater than 1ka (8/20 micro sec) with degree of protection ip 20 with 3 earthing electrodes of 3 meter length in grid, with high mast pipe cooecting link &including with all required accesorries. 90 item no 86:supplying and erecting isi mark gi pipe 75/80 mm dia. „b? class at position with accessories complete. specification no. cw plb/gp. 91 item no 87: supplying and fixing ms base plate 30x30x0.6 cm size fixed to the pole base either by welding or by set screws 12 mm. dia fixed at position. 92 item no 88:supplying, erecting & terminating xlpe unarmoured cable 1 core 70 sq. mm. copper conductor complete erected with provided lugs, laid in provided control panel/distribution boards / pipe as per specification no. cb lt/cu 93 item no 89:dismantling the existing cables of all types & size above 10 sq mm up to 50 sq. mm. 94 item no 90:dismantling the existing cables of all types & size above 50 sq. mm. 95 item no 91:dismantling the existing switchgears, db, and bus bar of any size complete with/ without board or angle iron frame complete. 96 supply, erection, testing & commissioningof street light at jayakwadi dam 97 item no 92:supplying and erecting mini feeder pillar triple pole with 200a fpmccb as incomer and 2 outgoing circuits with hrc fuse base and cartridge of 100a consists of aluminium bus bar 500 v 200 a complete erected in 14 gauge crca sheet box with supporting angles, self locks, gasket and slanting top to be erected on provided foundation as per specification no. sw swr/mfp 98 item no 93:supplying, erecting & terminating xlpe armoured cable 3½ core 120 sq. mm. aluminium conductor with continuous 12.97 sq. mm. (8 swg) g.i. earth wire complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. cb lt/al 99 item no 94:supplying, erecting & terminating xlpe armoured cable 3½ core 95 sq. mm. aluminium conductor with continuous 8.35 sq. mm. (10 swg) g.i. earth wire complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. cb lt/al 100 item no 95:supplying, erecting & terminating xlpe armoured cable 3½core 70 sq. mm. aluminium conductor with continuous8.35 sq. mm. (10 swg) g.i. earth wire complete erected withglands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. cb lt/al 101 item no 96:supplying, erecting & marking spmcb 0.5a to 5a in provided distribution board as per specification no. sw swr/mcb 102 item no 97:supplying & erecting frp box of size 150 x 125 x 100 mm, 2.7 mm thick complete on pole/wall as per specification no.cb sb 103 item no 98:supplying & erecting mains with 2x2.5 sq.mm frlsh copper pcc insulated wire laid in provided conduit/trunking/inside pole/bus bars or any other places as per specification no: wgma/ bw 104 item no 99:supplying, erecting & terminating xple armoured cable 4 core 16 sq. mm. aluminium conductor with continuous 5.48 sq. mm. (12 swg) g.i. earth wire complete erected with glands & lugs, on wall/trusses/pole or laid in provided trench/ pipe as per specification no.cb lt/al 105 item no 100: supplying and erecting led street light fitting suitable for above 70w 75w lamp, including lamp, with pf > 0.95 class ip 65 and above housing of pressure die cast aluminium alloy and heat sink extruded aluminium complete as per specification no fgodf/ fls2 106 item no 101: providing pipe type earthing with 40mm. dia. g.l. pipe or 20 mm dia. g.l. rod complete with all materials as per specification no. eaep 107 item no 102: supplying and erecting 12.5 m (clear height) high mast (top 150mm, bottom 360mm) with lowering and raising motorized unit, lantern carriage assembly suitable for max. 6 nos. luminaries and its control gear box, lightning finial arrangement for fixing aviation light and foundation bolts on provided foundation as per specification no. oh pl/hm (excluding luminaries ). 108 item no 103: making m 20 cement concrete foundation by considering the safe soil bearing capacity at site as 10 t/sq. m at 2 m depth including excavation and fixing provided nut bolts with the help of template, duly plastered as per design complete (for 12.5 m raising lowering high mast). 109 item no 104: supplying and erecting led flood light fitting of 120w, including lamp, with pf > 0.95,class ip 65 and above housing of pressure die cast aluminium alloy and heat sink extruded aluminium complete per specification no fgodf/fls 2 110 item no 105: supplying and erecting outdoor stand mounted feeder pillar for highmast of the same manufacturer with 32a tpn mcb incomer, single dial timer switch, 25a tp contactor for automatic switching of luminaries, 2 nos 9a contactors andraise/lower push button, and provision for termination of adequate size of incoming and outgoing cables erected in min. 14 swg crca sheet box with supporting angles, self lock, gasket and slanting top erected with cc foundation complete.note: rates are inclusive of foundation. 111 item no 106: supplying and laying (including excavation of suitable width & depth up to 90 cm) 50 mm outside dia. double wall corrugated pipes (dwc) of hdpe for enclosing cable below ground/road surface, to required depth complete. 112 item no 107:painting of steel tubular / rail / rsj pole above 6.0 m length along with street light pole brackets, clamps etc by scrapping the existing paint complete. specification no cw ptg/ptp. 113 item no 108:dismantling the existing cables of all types & size above 10 sq mm up to 50 sq. mm. 114 on grid solar power pack 115 item no 109:supplying, installing, testing and commissioning of 20 kwp capacity on grid solar power pack with gi mounting structure and inter connecting wires / cables without battery bank spv modules and solar power conditioning unit of required capacity complete, with 5 years on site performance warrantee. specification no. esd rt ong note: 2. for item no.4 6 2 add rs. 39657/ per kwp for on grid solar power pack above 11 kwp upto 100 kwp. 116 item no 110 :supplying and erecting iron, sheet metal work consisting of crca sheets, various sections of iron, plates, chequered plates, rods, bars, ms pipes, etc. for panel board or any other purpose with bending, cutting, drilling and welding complete erected at the position with necessary materials duly painted with one coat of red oxide and two coats of enamel paint to match the switchgears or as per directions by the authority. 117 item no 111 :supplying, erecting & marking tpmcb 40a to 63a in provided distribution board as per specification no. swswr/mcb 118 item no 112: supplying and erecting three phase 10 to 60 a net meter dlms compliance of accuracy class 1.0, 3 x 240v, 50 hz, with backlit lcd display, optical port and rj 232 port (measures import kwh, kvah, export kwh, kvah, net kwh, kvah,v, i, kw, 6 months history of energy) with wiring connections and mounting hardware on provided panels complete with calibration certificate from manufacturer. 119 item no 113: supplying and erecting three phase smart energy meter dlms compliance with 3x240v 50 cycles ac supply 10 60 a, isi mark, accuracy class 1.0 with backlit lcd display, measuring & display v, i, kw, kwh, pf, kva, kvar, md, day, week, month & with communication module configurable for gsm/wi fi, irda/bluetooth, complete provided panel with calibration certificate from manufacturer & duly wired with required size of pcc wires. 120 item no 114: charges for taking permission from various authority such as msedcl or else. ( it will be reimbursed only after submission of original reciepts by the contractor to this department.) 121 part b 122 sub estimate b:electrification of irb guest house at paithan,dist.chatrapati sambhajina gar. 123 item no 115: point wiring for light/bell/exhaust fan in pvc trunking (casing capping) with 1.5 sq.mm (2+1e) frlsh grade copper wire, modular type switch, earthing and required accessories as per specification no: wg pw/sw 124 item no 116 :point wiring for ceiling fan in pvc trunking (casing capping) with 1.5 sq.mm (2+1e) frlsh grade copper wire, modular type switch, earthing and required accessories as per specification no: wg pw/sw 125 item no 117 :secondary point wiring for additional light/ bell point in pvc trunking (casing capping) with 1.5 sq.mm (2+1e) frlsh grade copper wire with required accessories as per specification no: wg pw/sw 126 item no 118 :point wiring for independent plug in pvc trunking (casing capping) with 1.5 sq.mm (2+1e) frlsh grade copper wire, modular type switch, earthing and required accessories as per specification no: wg pw/sw 127 item no 119: wiring for plug on board with switch socket surface/concealed type, copper wiring and earthing and with modular accessories as per specification no: wgpw/cw 128 item no 120: supplying and erecting modular type 3 pin 6a multi socket with safety shutter, duly erected on provided plate and box with wiring connections complete 129 item no 121: supplying and erecting modular type switch 6a / 10a duly erected on provided plate and box with wiring connections complete. 130 item no 122:supplying and erecting modular type 3 pin 6 / 16a multi socket with safety shutter, duly erected on provided plate and box with wiring connections complete 131 item no 123:supplying and erecting modular type switch 16 / 20 a with indicator, duly erected on provided plate and box with wiring connections complete 132 item no 124:supplying & erecting crca sheet metal enclosures of 1.2mm thickness with 20a, 2 pin plug & earth socket and 20a, 3 pin plug top with 20a/30a single pole mcb having rated short circuit breaking capacity (icn) 10ka complete erected on angle iron/ gi frame. 133 item no 125:supplying and erecting modular type d.p. switch 32a with indicator, duly erected on provided plate and box with wiring connections complete. 134 item no 126:supplying and erecting modular type (two module) electronic step regulator for fan, duly erected on provided plate and box with wiring connections complete. 135 item no 127:supplying and erecting pvc surface modular switch box with doublemounting plate for 12 module duly erected 136 item no 128:supplying and erecting pvc surface modular switch box with double mounting plate for 6 module duly erected. 137 item no 129:supplying and erecting pvc surface modular switch box with double mounting plate for 3 module duly erected 138 item no 130:supplying and erecting pvc surface modular switch box with doublemounting plate for 2 module duly erected. 139 item no 131 :supplying and erecting modular type blanking plate one module, duly erectedon provided plate & box 140 item no 132: supplying and erecting led square / circular max. 7w down lighter/ panellight having pressure die cast aluminium housing, polystyrene diffuser having system lumens output of min. 770 lumens, min. efficacy of 110 lumen/w, cri>80, cct upto 6500k, beam angle of 120 deg., max. ripple of 5%, thd<10%, p.f. >0.95, operating range of 120 270v, surge protection of 2.5 kv, life class of 50,000 hrs. at l70b50, including driver, having mounting arrangement with board for surface type or spring loaded mounting clipscomplete with 3 years warranty 141 item no 133: supplying & erecting ready to use retrofit t8 led 18 / 20 tube light with polycarbonate body, heat sink, integrated hf electronic driver complete & compatible to t8 / t12 led luminaire by disconnecting starter & ballast if necessary. 142 item no 134 :supplying & erecting 10 12w, 230v integral type led lamp suitable for b 22 / e 27 base 143 item no 135 :supplying and erecting ding dong / electronic musical type call bell with heavy duty coil suitable to operate on 230v a.c. supply erected on polished double wooden block/sunmica block of suitable size. 144 item no 136:supplying and erecting energy saving ceiling fan 230 v a.c. 50 cycles 1200mm complete erected in position as per specification no. fg fn/cf 145 item no 137:supplying and erecting fan clamp of 30 x 5 mm. m.s. flat of required length and 10 mm. m.s. bolt and nuts erected with necessary hook of 10 mm. m.s. round bar and painted. 146 item no 138:supplying and erecting exhaust fan heavy duty 230 v a.c. 50 cycles 375/380 mm. 900 rpm complete erected in position as perspecifcation no. fg fn/exf 147 item no 139:supplying, installing, testing & commissioning split type variable speed inverter technology with minimum 3 to 1 convertible mode for compressor, room air conditioning unit 1.7tr to 2.0tr capacity having iseer minimum 3.8 to maximum 4.39 suitable to operate on 250v, 50 hz, a.c. supply having 1 no of air handling unit hi wall/floor mounting type complete with refrigerant r32 having copper condenser, minimum 2.5pm filter, self diagnosis feature, stabilizer free operation & temperature display on indoor unit, noise level maximum 50dba at position as per specification no. apac/ wac 148 item no 140:supplying, installing, testing & commissioning split type variable speed inverter technology with minimum 3 to 1 convertible mode for compressor, room air conditioning unit 2.1tr to 2.3tr capacity having iseer minimum 3.8 to maximum 4.39 suitable to operate on 250v, 50 hz, a.c. supply having 1 no of air handling unit hi wall/floor mounting type complete with refrigerant r32 having copper condenser, minimum 2.5pm filter, self diagnosis feature, stabilizer free operation & temperature display on indoor unit, noise level maximum 50dba at position as per specification no. apac/ wac 149 item no 141:supplying, installing, testing and commissioning of single phase, 230v, 50 hz, 2500 va digital pure sine wave inverter with backup time of ........ hrs. based on insulated gate bipolar transistor (igbt) technology complete as perspecification no. ap inv 150 item no 142:supplying and erecting 12v/200ah tubular battery with battery terminal wire,duly charged with 36 months warranty complete 151 item no 143:supplying and erecting mains with 2x1.5 sq.mm frlsh copper pvc insulated wire laid in provided conduit/trunking/inside pole/bus bars or any other places as per specification no: wg ma/bw 152 item no 144:supplying and erecting mains with 1x1.5 sq.mm frlsh copper pvc insulated wire laid in provided conduit/trunking/inside pole/bus bars or any other places as per specification no: wg ma/bw 153 item no 145:supplying and erecting mains with 2x2.5 sq.mm frlsh copper pvc insulated wire laid in provided conduit/trunking/inside pole/bus bars or any other places. as per specification no: wg ma/bw 154 item no 146:supplying and erecting mains with 1x2.5 sq.mm frlsh copper pvc insulated wire laid in provided conduit/trunking/inside pole/bus bars or any other places. as per specification no: wg ma/bw 155 item no 147: supplying & erecting mains with 2x4 sq.mm f.r copper pvc insulated wire laid in provided conduit/ trunking/ inside pole/ bus bars or any other places. as per specification no: wgma/ bw 156 item no 148 : supplying and erecting pvc trunking (pvc casing n capping) of size 25 mm with accessories on wall/ceiling as per specification no: wg ma/con. 157 item no 149 : supplying & erecting triple pole and neutral distribution board (tpndb), 3 pole/4 pole mccb as incomer & outgoing sp mcb (36 poles) or tp mcb of 12 ways (36 poles), with door, 1.2mm thickness, surface/flush mounted, on iron/gi frame (vertical busbar type) as per specification no. sw swr/mcbdb1 158 item no 150 : supplying & erecting triple pole and neutral distribution board (tpndb), spmcb of 8 ways / phase (24 poles), with door, 1.2mm thickness surface/ flush mounted, ip 43 protection on iron/gi frame (horizontal busbar type) as per specification no. sw swr/mcbdb 159 item no 151 :supplying, erecting & commissioning 4 pole rccb 80a, electromagnetic type with 30/100/300 ma sensitivity with earth leakage trip indication complete as perspecification no. sw rccb/rccb 160 item no 152 : supplying, erecting & marking spmcb 6a to 32a, b series (for lighting) in provided distribution board as per specification no. sw swr/mcb 161 item no 153: supplying, erecting & marking spmcb 6a to 32a, c series (for motor/power) in provided distribution board as per specification no. sw swr/mcb 162 item no 154: supplying, erecting & marking spmcb 40a to 63a, c series with rated short circuit breaking capacity (icn) 10ka in provided distribution board as per specification no. sw swr/mcb 163 item no 155:supplying, erecting & marking dpmcb 40a to 63a, c series with rated short circuit breaking capacity (icn) 10ka in provided distribution board as per specification no. sw swr/mcb 164 item no 156:supplying, erecting & marking tpmcb 40a to 63a, with rated short circuit breaking capacity (icn) 10ka in provided distribution board as per specificationno. sw swr/mcb 165 item no 157: supplying and erecting single pole and neutral distribution board (spndb), with 2 ways for incoming and 6 ways (6 poles) for outgoing sp mcbs, with door, 1.2mm thickness surface / flush mounted, ip 43 protection on iron / gi frame as per specification no. sw swr/mcbdb 166 item no 158: supplying and erecting blanking plate of suitable size on mcbdb 167 item no 159: supplying, erecting & terminating fr xlpe insulated, galvanised steel formed wire armoured (strip) cable 1100 v, 4 core 70 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. cb lt/al 168 item no 160: supplying, erecting & terminating fr xlpe insulated, galvanised steel formed wire armoured (strip) cable 1100 v, 4 core 25 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. cb lt/al 169 item no 161: supplying, erecting & terminating fr xlpe insulated, galvanised steel formed wire armoured (strip) cable 1100 v, 4 core 16 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. cb lt/al 170 item no 162:providing & erecting 4pole mccb, 415 v, 100a, rated short circuit breakingcapacity 25 ka (ics=100% of icu), adjustable thermal (overload) setting and fixedmagnetic setting with provided leads, provision for installation of shunt/uv/tripalarm contact. mccb with phase barriers on both sides, insulation withstandcapacity 800v, no line load bias in provided enclosure/panel as per specificationno. sw swr/mccb 171 item no 163:dismantling the existing light, fan, bell, clock, independent plug point,wiring including circuit mains of all types along with accessories etc.complete as per specification no: wg dm/pw 172 item no 164: dismantling the existing aluminium/copper mains, sub mains wiringupto 10 sq.mm. along with accessories etc. complete as per specification no:wg dm/pw 173 item no 165: dismantling the existing w.t. fluorescent fitting / s.v./ m.v. / m.h. lamp/led fitting from wall with brackets and making the site as original complete. 174 item no 166:dismantling the existing ceiling fan /exhaust fan / cabin fan / bracket fancomplete with accessories, g.i. down rod, frame etc. and making the site clear 175 item no 167:dismantling the existing switchgears, db, and bus bar of any size complete with/ without board or angle iron frame complete. 176 item no 168: making the site clear of dismantled db and switch gears by refilling the holes with cement mortar & finishing in an approved manner complete. 177 item no 169:providng earthing with galvanized iron earth plate size 60 x 60 x 0.6 cmcomplete with all materials, testing & recording the results as per specification no.ea ep 178 item no 170:supplying, installation and testing of maintenance free earthing comprising of electrode of 17.2 mm diameter low carbon steel with 250 micron molecular copper bonded earthing rod of length 3m along with 25 kg carbon based environment friendly back fill ground enhancing compound required to fill up the excavated earth with required quantity complete, and recording the resultsspecification no. ea mobi 179 item no 171 : supplying and erecting gi wire of high purity of required sizes used for earthingor any other purposes on wall with necessary g. i. clamps fixed on wall/cable/ conduit with screws complete.. 180 item no 172 : providing & erecting 9 m high (clear height) galvanised octagonal pole withfoundation bolts having bottom of 155 mm a/f, top 70 mm a/f on provided foundation as per specification no. oh pl/opl 181 item no 173:supplying and erecting integrated led street light fitting 60w ip65 & ik08 class having single piece pressure die cast aluminium housing, having system lumens output of min. 6600 lumens, min. efficacy of 110 lumen/w, cri>70, cct upto 6500k, thd<10%, p.f. >0.95, operating range of 140 270v, inbuilt surge protection of 10 kv, life class of 50,000 hrs. at l70b50, including driver complete with 3 years warranty as per specification no fg odf/fls2 182 item no 174:making cement concrete foundation including excavation (60 x 60 x 150) cmeep in 1:3:6 cement concrete 20 x 25 mm stone metal, (45 x 45 x 45) cm /45cm dia. x 45 cm height plinth duly plastered, with necessary curing and finishing complete. (above 6 m to 9 m poles) 183 item no 175:supplying, erecting & terminating fr xlpe insulated, galvanised steel formed wire armoured (strip) cable 1100 v, 4 core 10 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. cb lt/al 184 item no 176 : supplying and erecting street light bracket for erection of single fitting madefrom 40 mm. dia ‘b’ class g.i. pipe 1.0 m. in length along with pole cap of 300mm length 100 mm dia duly welded as per specification no. fg bkt/bpc 185 item no 177 : dismantling the existing pole above 6 m height with brackets, clamps,insulators, stay from the c.c. foundation and making the site clear by refilling the pits with excavated materials and bringing it to the ground level. 186 item no 178: supplying and laying (including excavation of suitable width & depth up to 90 cm) 50 mm outside dia. double wall corrugated pipes (dwc) of hdpe for enclosing cable below ground/road surface, to required depth complete. 187 item no 179: providing pipe type earthing with 40mm. dia. g.i. pipe or 20 mm dia. g.i. rodcomplete with all materials testing and recording the results as per specification no.ea ep 188 item no 180 : supplying and erecting integrated led street light fitting 26 to 30w ip65 ik08 class having single piece pressure die cast aluminium housing , havingsystem lumens output of min. 2600 lumens, min. efficacy of 100 lumen/w,cri>70, cct upto 6500k, thd<10%, p.f. >0.95, operating range of 140 270v,inbuilt surge protection of 10 kv, life class of 50,000 hrs. at l70b50, including driver complete with 3 years warranty as per specification no fg odf/fls2. 189 item no 181 :supplying and erecting modular type bell indicator, duly erected on provided plate and box with wiring connections complete. 190 item no 182 :supplying and erecting ultra violet storage type water purifier (ro+uv+uf)with softener for safe drinking water consisting of uv germicidal tube of 8wcapacity choke made of copper wire and two indicator lamps with output ofpurified water minimum 0.33 litre/min with activated carbon filter and softener operating on 230v, single phase a.c. supply with uv fail & filter changeindication system .(for tds more than 200) 191 item no 183: supplying, erecting, testing and commissioning self contained water cooler230/250v 50hz nominal cooling capacity of 150 litres per hour and storagecapacity 150 litres with partially stainless steel body as per specification no. apwcr/wc 192 item no 184: supplying and erecting storage type water heater 25 litres capacity havingstanding loss <0.511kwh/24hour/45°c, high impact resistance engineeringplastic body with anti corrosive high grade steel inner tank, heatingelement having hard water & corrosion protection, with minimum 3 safetyprotections (i.e. thermostat & thermal function cut out, valve) with totalpressure 8 bar withstanding capacity duly tested and marking sr. no. and date of 193 item no 185: supplying double door refrigerator domes tic type of 300 to 360 litres storagecapacity, minimum 5 star inverter type, stabilizer free operation suitable foroperation on 100v/300 v, 50hz with automatic temperature con trol, shall bemarked on unit for sealed unit in refrigeration system and marking sr. no. and date of erection complete 194 item no 186:supplying and erecting iron work, sheet metal work consisting of crca sheets, various sections of iron, plates, chequered plates, rods, bars, ms pipes, etc. for panel board or any other purpose with bending, cutting, drilling and welding complete erected at the position with necessary materials duly painted with one coat of red oxide and two coats of enamel paint to match the switchgears or as per directions by the authority. ...

Military Engineer Services - Maharashtra

39526264 repairs to area drainage system, culvert, hume pipes and storm drainage system and connected b / r work in otm / md accn at aicts, ngm, ogm, fafa qtrs, dca, vbv, map ph i, dad, pcda ( o ) and nadfm area under age b / r i of ge ( south ) pune...

Department Of Defence - Maharashtra

39434188 bids are invited for steel 20 mm dia tata oblique jindal , steel 16 mm dia tata oblique jindal , steel 12 mm dia tata oblique jindal , steel 10 mm dia tata oblique jindal , steel 08 mm dia tata oblique jindal , binding wire gauge size 16 to 20 , timber 2nd class well seasoned hard wood planks plank 12 inch x 1 pt 5 inch x10 inch , lime slacked , pvc pipe 4 inch dia 6 mtr length make ashirvad oblique finolex oblique prince , rcc hume pipe dia 12mm connected with color rcc pipes in 2 pt 5 mtr length class np 2 with sulphate resistance cement suitable for joining with flexible rubber ring , hume pipe 300 mm dia 2m length duly connected with color r c c pipes in class np 2 with sulphate resistance cement suitable for jointing with flexible rubber ring confined gasket joints , inter link chain 4 mm dia mesh size 4 inch , icbp 80 mm conceret block interlocking tiles 6 cm thick of size 0 pt 225 meter x 0 pt 1125 mtr or 0 pt 0253 sqm area per no...

Western Coalfields Limited - Maharashtra

39018448 tender for laying of rcc hume pipes and other miscellaneous works in wardha river for temporary by pass traffic due to unsafe wardha river bridge (mungoli) at mungoli sub area of wani area....

Nagar Panchayat - Maharashtra

38956195 supply of construction materials park and other materials for khalapur nagar panchayat. 1 chain link jali 50mmx50mmx8mm thik 2 tor steel 3 structural steel 4 r.c.c.cover for insepection chember of size 75mm shik per sqft 5 w.c.pan orrisa 27 size 6 wash basin 7 urinal pot 8 colour glazed tiles 9 white cement 10 cement 43 grade 50kg 11 g.i.corrugated sheet ( colour coated ) 12 g.i.plain sheet 13 decorative ply vener 4mm thick 14 oil bound paint 15 oil paint 16 primer 17 water proofing items 18 thinner 19 lime 20 putty 21 brush 22 scraping sand paper 23 neru 24 terpentine oil 25 apex 26 red oxide 27 rcc hume pipe np3 class with collar of size 450 dai 28 rcc hume pipe np3 class with collar of size 600 dai 29 kadapa stone 30 bricks 31 metal ( all size ) 32 dubber 33 sand 34 300mm hume pipe 49 g.i.pipe b clss 15 mm 50 g.i.pipe b clss 25 mm 51 g.i.pipe b clss 40 mm 52 g.i.pipe b clss 60 mm 53 g.i.pipe b clss 90 mm 54 g.i.pipe b clss 110 mm 55 g.i.pipe b clss 150mm 56 g.i.pipe b clss 200mm 57 binding wire...

Directorate Of Municipal Administration - Maharashtra

38843485 tender for yearly supply and installation of electrical materials, electrical poles, led lights and accessories etc., reparing of led lights/high must for year 2023 24 , supplying and erecting metal clad distribution board 240v, 2 way, 16a per way & neutral bar connector complete erected on iron / gi frame as per specification no. sw swr/mdb , supplying, erecting & marking tpmcb 6a to 32a,in provided distribution board as per specification no. sw swr/mcb , supplying, installing, testing and commissioning solar street light pole comprising of 14w led fitting, 12v 36ah maintenance free lithium battery, min. 75wp spv module, ms powder coated battery box weather proof, mounted on 75/80 mm dia. b grade gi pole of 6 m. height along with brackets, foundation, earthling and necessary accessories complete. specification no. esd sol stl (with 5 years warrantee ) , making trench of suitable width and depth in soft soil for laying provided lt cable up to and including 16 sq.mm complete as per specification no. cw exn ctr , making trench of suitable width and depth in hard murum / tar road for laying provided lt cable of 16 sq. mm & above and covered with half round hume pipe complete as per specification no. cw exn ctr , supplying, erecting & terminating xlpe armoured cable 2 core 6 sq. mm. aluminium conductor with continuous 5.48 sq. mm. (12 swg) g.i. earth wire complete erected with glands & lugs, on wall/trusses/pole or laid in provided trench/ pipe as per specification no.cb lt/al , supplying, erecting & terminating xlpe armoured cable 2 core 10 sq. mm. aluminium conductor with continuous 5.48 sq. mm. (12 swg) g.i. earth wire complete erected with glands & lugs, on wall/trusses/pole or laid in provided trench/ pipe as per specification no.cb lt/al , supplying, erecting & terminating xlpe armoured cable 4 core 6 sq. mm. aluminium conductor with continuous 5.48 sq. mm. (12 swg) g.i. earth wire complete erected with glands & lugs, on wall/trusses/pole or laid in provided trench/ pipe as per specification no.cb lt/al , supplying, erecting & terminating xlpe armoured cable 1100 v.3½ core 185 sq. mm. aluminium conductor with continuous 12.97 sq. mm. (8 swg) g.i. earth wire complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. cb lt/al , supplying, erecting & terminating xlpe armoured cable 3½ core 25 sq. mm. aluminium conductor with continuous 5.48 sq. mm. (12 swg) g.i. earth wire complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. cb lt/al , supplying and erecting isi mark g.i. pipe pole ‘b’ grade 80 mm dia 6 m long with pole cap, base plate in provided foundation as per specification no. oh pl/gip , supplying and erecting steel tubular swaged pole 139.7 x 114.3 x 88.9 mm. dia with 4.5x3.65x3.25 mm thickness (4.5 + 1.75 + 1.75 m) length respectively and total 8 m long with pole cap, base plate in provided foundation.(weight 101 kg.) as per specification no.oh pl/stp , supplying and erecting steel tubular swaged pole 139.7 x 114.3 x 88.9 mm. dia with 4.5x3.65x3.25 mm thickness (5 + 1.75 + 1.75 m) length respectively and total 8.5 m long with pole cap, base plate in provided foundation.(weight 109 kg.) as per specification no.oh pl/stp , supplying and erecting steel tubular swaged pole 165.1 x 139.7 x 114.3 mm. dia with 4.5 x 4.5 x 3.65 mm thickness ( 5 + 2 + 2 m ) length respectively and total 9 m long with pole cap, base plate in provided foundation (weight 147 kg) as per specification no.oh pl/stp , supplying and erecting street light bracket made from 25 mm. dia ‘b’ class g.i. pipe, 0.6 m in length along with pole cap of 300 mm length and 80 mm dia duly welded with provided leads as per specification no. fg bkt/bpc , supplying and erecting street light bracket for erection of single fitting made from 40 mm. dia ‘b’ class g.i. pipe 1.0 m in length along with pole cap of 300 mm length 100 mm dia duly welded as per specification no. fg bkt/bpc , supplying and erecting street light bracket for erection of double fitting on tubular welded pole with 40 mm. dia 1.0 m long “b” grade g.i. pipe along with pole cap of 125mm dia 600 mm long duly welded as per specification no. fg bkt/bpc , supplying & erecting frp box of size 300 x 200 x 125 mm, 2.7 mm thick complete on pole/wall as per specification no. cb sb , supplying & erecting mains with 2x2.5 sq.mm f.r copper pvc insulated wire laid in provided conduit/trunking/inside pole/bus bars or any other places. as per specification no: wgma/bw , providing pipe type earthing with 40mm. dia. g.l. pipe or 20 mm dia. g.l. rod complete with all materials as per specification no. eaep , supplying and erecting isi mark gi pipe 25 mm. dia. ‘b’ class at position with accessories complete. specification no. cw plb/gp. , making cement concrete foundation including excavation ( 45 x 45 x 120 ) cm deep in 1:3:6 cement concrete, 20 to 25 mm stone metal, (45 x 45 x 45) cm / 45 cm dia. x 45 cm height plinth duly plastered,with necessary curing and finishing complete. (for 6 m pole) , making cement concrete foundation including excavation (60 x 60 x 150) cm deep in 1:3:6 cement concrete 20 x 25 mm stone metal, (45 x 45 x 45) cm /45 cm dia. x 45 cm height plinth duly plastered, with necessary curing and finishing complete. (above 6 m to 9 m poles) , making cement concrete foundation including excavation (60 x 60) cm x deep 1/6 of pole length in 1:3:6 cement concrete 20 x 25 mm stone metal, 45 cm x 45 cm x 45 cm /45 cm dia. x 45 cm. height plinth duly plastered, with necessary curing and finishing complete.(for above 9 m poles) , making m 20 grade reinforced cement concrete foundation by considering the safe soil bearing capacity as 10 t/sq.m at 1.5 m depth including supply of steel, concrete, excavation, fixing provided nut bolts with the help of template, duly plastered as per design complete (for 3 to 5m octagonal / conical gi pole). , making m 20 grade reinforced cement concrete foundation by considering the safe soil bearing capacity at site as 10 t/sq.m at 1.5 m depth including supply of steel, concrete, excavation and fixing provided nut bolts with the help of template, duly plastered as per design complete (for 9m & 10m high octagonal /conical gi pole). , making m 20 grade reinforced cement concrete foundation by considering the safe soil bearing capacity at site as 10 t/sq. m at 1.5 m depth including supply of steel, concrete, excavation and fixing provided nut bolts with the help of template, duly plastered as per design complete ( for 11m & 12.5m high octagonal /conical gi pole). , making m 20 cement concrete foundation by considering the safe soil bearing capacity at site as 10 t/sq. m at 2 m depth including excavation and fixing provided nut bolts with the help of template,duly plastered as per design complete (for 12.5 m raising lowering high mast). , providing & erecting 3 m high (clear height) galvanised octagonal pole with foundation bolts having bottom of 130 mm a/f, top 70 mm a/f on provided foundation as per specification no. ohpl/opl , providing & erecting 4 m high (clear height) galvanised octagonal pole with foundation bolts having bottom of 130 mm a/f, top 70 mm a/f on provided foundation as per specification no.ohpl/opl , providing & erecting 5 m high (clear height) galvanised octagonal pole with foundation bolts having bottom of 130 mm a/f, top 70 mm a/f on provided foundation as per specification no. ohpl/opl. , providing & erecting 6 m high (clear height) galvanised octagonal pole with foundation bolts having bottom of 130 mm a/f, top 70 mm a/f on provided foundation as per specification no. ohpl/opl , providing & erecting 7 m high (clear height) galvanised octagonal pole with foundation bolts having bottom of 130 mm a/f, top 70 mm a/f on provided foundation as per specification no.ohpl/opl. , providing & erecting 8 m high (clear height) galvanised octagonal pole with foundation bolts having bottom of 135 mm a/f, top 70 mm a/f on provided foundation as per specification no. ohpl/opl , providing & erecting 9 m high (clear height) galvanised octagonal pole with foundation bolts having bottom of 155 mm a/f, top 70mm a/f on provided foundation as per specification no. ohpl/ opl , providing & erecting 10 m high (clear height) galvanised octagonal pole with foundation bolts having bottom of 175 mm a/f, top 70 mm a/f on provided foundation as per specification no. ohpl/opl , providing & erecting 11 m high (clear height) galvanised octagonal pole with foundation bolts having bottom of 210 mm a/f, top 90 mm a/f on provided foundation as per specification no. ohpl/opl , providing & erecting 12 m high (clear height) galvanised octagonal pole with foundation bolts having bottom of 240 mm a/f, top 90 mm a/f on provided foundation as per specification no. ohpl/opl , supplying and erecting outdoor stand mounted feeder pillar for highmast of the same manufacturer with 32a tpn mcb incomer, single dial timer switch, 25a tp contactor for automatic switching of luminaries, 2 nos 9a contactors and raise/lower push button, and provision for termination of adequate size of incoming and outgoing cables erected in min. 14 swg crca sheet box with supporting angles, self lock, gasket and slanting top erected with cc foundation complete. , providing and erecting galvanised 1000mm single arm sword type bracket with frp dome and ball as per specification no. ohpl/pbkt , providing and erecting galvanised 1000mm double arm sword type bracket with frp dome and ball as per specification no. ohpl/pbkt , supplying, erecting & terminating xlpe armoured cable 3 core 2.5 sq. mm. aluminium conductor with continuous 5.48 sq. mm. (12 swg) g.i. earth wire complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. cb lt/al , providing earthing with copper earth plate size 30 x 30 x 0.315 cm complete with all materials, testing & recording the results as per specification no. ea ep , supplying and erecting aluminium strip of required sizes used for earthing on wall and/or any other purpose with necessary aluminium clamps fixed on wall painted with bituminous paint in an approved manner with joints required. as per specification no eaep. , supplying and erecting gi earth wire of high purity of different sizes used for earthing or any other purposes on wall with necessary g. i. clamps fixed on wall/cable/ conduit with screws in an approved manner. , supplying and erecting aluminium strip of required sizes used for earthing on wall and/or any other purpose with necessary aluminium clamps fixed on wall with insulating and non corrosive bond in an approved manner with required joints. as per specification no. eaep. , supplying and erecting led street light fitting suitable for above 70w 75 lamp, including lamp, with pf > 0.95 class ip 65 and above housing of pressure die cast aluminium alloy and heat sink extruded aluminium complete per specification no fgodf/fls2 , supplying and erecting led street light fitting 100w, including lamp, with pf > 0.95 class ip 65 and above housing of pressure die cast aluminium alloy and heat sink extruded aluminium complete per specification no fg odf/fls 2. , making trench of suitable width and depth in soft soil for laying provided lt cable up to and including 16 sq.mm complete as per specification no. cw exn ctr , supplying, erecting & terminating xlpe armoured cable 2 core 4 sq. mm. aluminium conductor with continuous 5.48 sq. mm. (12 swg) g.i. earth wire complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no.cb lt/al , supplying and erecting isi mark g.i. pipe pole ‘b’ grade 80 mm dia 6 m long with pole cap, base plate in provided foundation as per specification no. oh pl/gi , supplying and erecting street light bracket made from 40 mm. dia ‘b’ class g.i. pipe, 0.6m. in length along with pole cap of 300 mm length and 80 mm dia duly welded with provided leads as per specification no. fg bkt/bpc , supplying & erecting frp box of size 150 x 125 x 100 mm, 2.7 mm thick complete on pole/wall as per specification no. cb sb , supplying & erecting mains with 2x1.5 sq.mm f.r copper pvc insulated wire laid in provided conduit/trunking/inside pole/bus bars or any other places as per specification no: wgma/bw , providing pipe type earthing with 40mm. dia. g.l. pipe or 20 mm dia. g.l. rod complete with all materials as per specification no. eaep , supplying and erecting isi mark gi pipe 15 mm dia. ‘b’ class at position with accessories complete. specification no. cw plb/gp. , making cement concrete foundation including excavation ( 45 x 45 x 120 ) cm deep in 1:3:6 cement concrete, 20 to 25 mm stone metal, (45 x 45 x 45) cm / 45 cm dia. x 45 cm height plinth duly plastered,with necessary curing and finishing complete. (for 6 m pole) , supplying, erecting & terminating xlpe armoured cable 4 core 10 sq. mm. aluminium conductor with continuous 5.48 sq. mm. (12 swg) g.i. earth wire complete erected with glands & lugs, on wall/trusses/pole or laid in provided trench/ pipe as per specification no.cb lt/al , supplying and laying (including excavation of suitable width & depth up to 90 cm) 50 mm outside dia. double wall corrugated pipes (dwc) of hdpe for enclosing cable below ground/road surface, to required depth complete , ? ?? ?? ?? ?????? ???? ???? ? ?????? ??????? ?? (? ???? ????? ) , ? ? ?? ???????? ????????? ???? ???? (???? ????? ? ??? ?????????? ????? ??? ) , ??????? ???? ?? ???? ???? ???????? ???? (??????? ?? ) , ??????? ???? ??? ??????? ???? ???? (????? ????? ) , ups 800 va , spanner set tool kit box (bosch) , 11 kv discharge rod (3 piece set) , 1.5 sq.mm. 3 core flexible copper wire , led tube light 18 w , exhaust fan 300 mm , air conditioner 2 ton , air conditioner 1.5 ton , air conditioner 1 ton , table fan 400 mm , wall fan 400 mm , ceiling fan 1200 mm , providing anf installation of 1 nos power point (with all material) , providing anf installation of 1 nos light point (with all material) , invertor led lamp 30 w , invertor led lamp 24 w , invertor led lamp 18 w , 40/36 flexible copper wire , armoured cable 2c,25sqmm,aluminium , armoured cable 2c,16sqmm,aluminium , armoured cable 2c,10sqmm,aluminium , armoured cable 2c,6sqmm,aluminium , armoured cable 2c,4sqmm,aluminium , water proof insulation tape , street light led 12 18 w , street light led 26 36 w , cfl holder , pvc insulation tape , main switch with kitkat fuse 100a, 1 ph , main switch with kitkat fuse 63a, 1 ph , 2c, 10 sqmm service wire aluminium , 2c, 6 sqmm service wire aluminium , 2c, 4 sqmm service wire aluminium , 3/20 copper wire , 2.5sqmm flexible copper wire , 1.5sqmm flexible copper wire , mcb 3 ph,63a , mcb 3 ph,100a , mcb 1 ph, 32 a , mcb 1 ph, 63 a , mcb 1 ph, 100 a , mcb 1 ph, 6 a , elcb 63 a/415 , kit kat fuse 100 a , kit kat fuse 63 a , kit kat fuse 32 a , main switch with kitkat fuse 100 a, 3 ph , main switch with kitkat fuse 63 a, 3 ph , main switch with kitkat fuse 32 a, 3 ph , patripeti 2*3 feet (pole box) , patripeti 2*2.5 feet (pole box) , rotor holder for tube rod fitting , drum holder for tube light starter fitting , patrikan for side holder fitting for 40 w tube light , starter for tube light , tube light choke for 40 w (electronic) , tube light choke for 40 w (copper) , tube light rod 40 watt , led lamp 24 watt threaded / pin type , led lamp 30 watt threaded / pin type , led lamp 40 watt threaded / pin type , cfl lamp 85 watt threaded / pin type , aac gnat conductor , aac ant conductor , shockle,shockle patti,shockle nut bolt , gi wire 14 no. , bobin for cable hanging purpose , cfl lamp 65 watt threaded / pin type , stree light tube fixture for 40 w (heavy duty) , top vocer for tube light fixture , tube ligth patti for 40 w , bracket for led light fitting (18 36 w) 4 feet in length (pipe) , khekda clamp for gulder pole of 3*4 inch for 3/4 inch bracket with nut & bolts , street light led 20 25 w , bracket for tube light fixture (pipe) 3/4 inch and 5 feet length , clamp for 3*4 gulder pole (i section) for 3/4 inch bracket size with nut & bolts , clamp for 2.5*3 gulder pole (i section) for 3/4 inch bracket size with nut & bolts , clamp for 2.5*3 gulder pole (i section) for 1.25 inch bracket size with nut & bolts , khekda clamp for gulder pole of 2.5*3 inch for 3/4 inch bracket eith nut & bolts , khekda clamp for gulder pole of 3/4 inch for 1.25 inch bracket eith nut & bolts , ?????????? ? ??.????.? , ????? ??? ??????? (exide ????? ??????? ) , ????? ?? ????? ?? ??????? ????? , ?????????? ???????? , ?? ? ???? , ????? ???? ???? ??????? , repairing of led street light, 20 24 w, (with required material) , repairing of led street light, 26 36 w, (with required material) , repairing of led street light, 40 48 w, (with required material) , repairing of led street light, 60 w, (with required material) , repairing of led street light, 70 75 w, (with required material) , repairing of led ( fiood type ) street light 50 w(with required material) , repairing of led ( fiood type ) street light 70 80 w(with required material) , repairing of led ( fiood type ) street light 90 100 w(with required material) , repairing of led ( fiood type ) street light 120 w(with required material) , repairing of led ( fiood type ) street light 150 w(with required material) , repairing of mini high must 110 watt led (4 nos)flood light , rsj pole 125x70 ,8 mtr long , lt stay set , rsj pole 125x70 ,8 mtr stud...

Tata Power Company Limited - Maharashtra

38817191 tender for civil work ri of road after ehv cable laying in mbpt area,mumbai for r i work for asphalt / paver block area at mbpt road qty area as 1600 m x 2.50 m of qty. 1 exc. for road, trenches pits etc. in ordinary soil mixed with boulders of max. dia. 700mm, including removal of vegetation, dewatering wherever necessary etc. complete. with pump wherever necessary etc. complete. including shifting and stacking excavated material within an initial lead of 100 m, and then removal and disposing off excavated earth in mcgm / mbmc approved dumping areas (measurements shall be based on plan dimensions of pcc. no additional payment will be made for slopes, working area, shoring, etc.) for depth of excavation 0.00 to 1.50 mtrs. rate to be including of royalty providing all materials, tools equipment & barricadding etc. 2,640.00 m3 2.0 preparing & consolidating subgrade using vibratory roller so as to obtain 95 to 98% density complete as directed by engineer incharge 4,000.00 m2 3.0 providing ,laying & fixing 250mm consolidated thickness rubble packing on subgrade for formation of upper sub base. using approved quality graded stone aggregates materials includes shifting & placing etc completed as per drawings ,specification & as directed by eic. 1,250.00 m3 4.0 providing ,laying & compaction for 160mm thick (+/ 25mm variation ) metal / granular sub base (gsb) of grade iii /iv as mentioned in drawing with dressing of excavated surface,shifting & spreading of aggregate manually ,compaction by compactor,conducting compaction test etc completed as per drawings ,specification & as directed by eic. compactor (10 ton vibratory roller / plate compactor shall be used as per instructed by eic) will be in scope of scope of contractor 640 m3 5.0 providing ,laying & compaction for 100mm full grout for formation of upper sub base. using approved quality graded stone aggregates screening and binding materials includes shifting ,placing & compaction with compactor etc completed as per drawings ,specification & as directed by eic. dosage 2 to 3 kg/sqm bitumen vg30 compactor (10 ton vibratory roller) will be in scope of contractor 4000 m2 6.0 prov & lay100mm thick asphalt macadam including prime coat with specified graded stone aggregate for levelling course including loading of aggregates with f.e loader and hot mixing of bitumen filler @ 3.5% with hot mix plant trans. the mix material with tipper to pavers and laying with sensor pavers finisher to the req. level,grades,and rolling with 8 10 ton vibratory roller to achieve the desired density etc.complete in all respect as per the approved job mix formula as per morth clause 509. 4000 m2 7.0 providing & laying 50mm thick asphalt concrete (0.75kg/m2),comparising of thin applicatio of fine aggregate premixed with bituminous binder including cleaning wherever required and applying tack coat (bitumen 0.75kg/m2).bitumen content 6.0% of mix and covered with stone dust so as to obtain smooth finish including material tools etc.laying by paver finisher and copaction by 10 to 12 ton roller. 4000 m2 8.0 dismentling/breaking of pcc of 300mm depth,conveying the dismentling material and disposing outside premises with all lead and lift etc completed as directed by eic 960 m3 9.0 providing and fixing interlocking concrete pavers of crushing strength 50n/sq mm. concrete pavers shall be uniformly shaped with thickness 60 mm up to 100mm thk.the paver shall be placed on sand bed of 50mm thickness with proper compacting and in proper level grade and camber as directed . the side joints shall be filled by m20 grade pcc. 1,000.00 m2 10.0 providing & laying 75mm thick plain cement concrete (pcc) m15 grade on wbm for again formation of upper concrete base.including curing,compacting,de watering wherever necessary,etc completed as per drawings,specificatios & ass directed by eic. 100 m3 11.0 providing & laying hume pipe confirming to is 458 (class np2) in line and level in required slope or as directed includingproviding all materials pipes etc., cement jointing the collars with 1:1 cement mortar including 50mm thick and sufficient wide (to cover at least 25 mm beyond the joint), m 10 concrete below joints but excluding excavation for 300 mm dia. 100 rm for r i work for cc road at mbpt road area 2800 m x 3.50 m of qty. 12.0 exc. for road, trenches pits etc. in ordinary soil mixed with boulders of max. dia. 700mm, including removal of vegetation, dewatering wherever necessary etc. complete. with pump wherever necessary etc. complete. including shifting and stacking excavated material within an initial lead of 100 m, and then removal and disposing off excavated earth in mcgm / mbmc approved dumping areas (measurements shall be based on plan dimensions of pcc. no additional payment will be made for slopes, working area, shoring, etc.) for depth of excavation 0.00 to 1.50 mtrs. rate to be including of royalty providing all materials, tools equipment & barricadding etc. 4,750.00 m3 13.0 preparing & consolidating subgrade using vibratory roller so as to obtain 95 to 98% density complete as directed by engineer incharge 9,800.00 m2 14.0 providing ,laying & compaction for 160mm thick (+/ 25mm variation ) metal / granular sub base (gsb) of grade iii /iv as mentioned in drawing with dressing of excavated surface,shifting & spreading of aggregate manually ,compaction by compactor,conducting compaction test etc completed as per drawings ,specification & as directed by eic. compactor (10 ton vibratory roller / plate compactor shall be used as per instructed by eic) will be in scope of scope of contractor 1600 m3 15.0 providing ,laying & compaction for 100mm consolidated thickness water bound macadam (wbm) on gsb for formation of upper sub base. using approved quality graded stone aggregates screening and binding materials includes shifting ,placing & compaction with compactor.providing all materials, tools equipment & barricadding etc. completed as per drawings ,specification & as directed by eic. compactor (10 ton vibratory roller) will be in scope of contractor 1000 m 16.0 providing & laying 75mm thick plain cement concrete (pcc) m15 grade on wbm for again formation of upper concrete base.including curing,compacting,de watering wherever necessary,etc completed as per drawings,specificatios & ass directed by eic. 735 m3 17.0 providing & laying of impermeable pvc sheet 75 micron thick transparent/white in colour on pcc sub base & nailed to the lower base with concrete nails etc completed as per drawings ,specification & as directed by eic. 9800 m2 18.0 providing ,laying placing of 300 mm thick concrete of m 35 grade on pvc membrane with line, level , slope, etc as per specification & as mentioned in drawings. scope includes,placing & compaction of concrete ,curing by ponding method, fixing & removing of shuttering, fixing of sleeves/pipes, providing & applying concrete bonding chemical etc. formwork materials (ms channel ) vibrator,chipper/breaker ,tools & tackles etc will be in scope of subcontractor . reinforcement will be paid extra 2940 m3 19.0 longitudinal joint to be placed on pavement width more than one lane/3 rmt joints will be cut by concrete saw after 6 14 hrs.of placing of concrete & joints shall be filled with bitumen sealant in 25mm deep (butt type) from top,includes cleaning ,removal of dust etc.concrete face of long.joint will be painted by bitumen paint before placing of concrete etc complete as per drawing,spec. & as directed by eic.bitumen paint, bitumen sealant, concrete saw cut machine will be in scope of contractor. 2800 rmt 20.0 charges for formation of expansion joints (minimum 3mm width ,340mm deep) expansion joints to be placed in interval of every 32 rmt , providing & placing 100mm long 3mm thick pvc cap filled with compressible material over sheathed end of each dowel . joints to be filled with bitumen joint sealant ( 20mm deep butt type from top) etc.completed as per specification ,drawings & as directed by eic.bitumen paint, bitumen sealant, pvc cap,concrete saw cut machine will be in scope of contractor. 306.25 m 21.0 const. joint/transvers joint having min.3mm width & 60mm deep to be placed in interval of every 4 rmt .joints will be cut by concrete saw after 6 14 hrs.of placing of concrete & filled with bitumen joint sealant (20mm deep butt type from top ) after 21 days of placing of concrete. including cleaning ,removing of dust with air blower etc. competed as per drawing,spec. & as directed by eic. bitumen paint, bitumen sealant, concrete saw cut machine will be in scope of contractor. 2450 m 22.0 supplying, cleaning, cutting, welding, lapping, bending as per dwgs. & placing in position at all locations and levels including binding with soft annealed 16g block wire etc. complete as directed by tpcls engineer. 32mm dia ms round steel 12.5 mt 23.0 supplying, cleaning, cutting, welding, lapping, bending as per dwgs. & placing in position at all locations and levels including binding with soft annealed 16g block wire etc. complete as directed by tpcls engineer.12mm dia tmt steel 5 mt 24.0 dismentling/breaking of pcc of at all depth,conveying the dismentling material and including shifting and stacking material within an initial lead of 100 m, and then removal and disposing off in mcgm / mbmc approved dumping areas disposing outside premises with all lead and lift etc completed as directed by eic.rate to be including of royalty 1680 m3...

Western Railway - Maharashtra

38699202 tender for ccg vr section : andheri proposed 1800 mm dia rcc hume pipe ( 1 nos ) storm water drain by micro tunneling method under the railway tracks near culvert n0. 38 at km 20 / 13 14 for mcgm....

Western Railway - Maharashtra

38698716 tender for ccg vr section : malad proposed 1800 mm dia rcc hume pipe ( 2 n0s ) storm water drain by micro tunneling method under the railway tracks near culvert n0. 56 at km 29 / 09 10 for mcgm....

Bhabha Atomic Research Centre - Maharashtra

38682311 supply, installation, testing and commissioningof perimeter cctv and lighting system from pp dump yard to sg including five years of maintenance, barc, mumbai, trombay 400085. 1 outdoor bullet ip camera along with mounting accessories as per tss no. 1 2 outdoor bullet / box ip camera along with mounting accessories as per tss no. 2 3 ptz ip camera along with pole mount and mounting accessories and 45 watt or higher poe+ injector as per tss no. 3 4 industrial grade l2 switchas per tss no. 4 5 single mode 1g sfp modules as per tss no. 5 6 single mode 10g sfp modules as per tss no. 6 7 l3 switch as per tss no. 7 8 rack mountable management serverto support minimum 90cameras as per tss no. 8 9 8 port lcdkvm switch with keyboard & mouse along with all cable and accessories as per tss no. 9 10 recording and storage server with 1 month continuously recording as per tss no. 10 11 workstation as per tss no. 11 12 vms license for cameras with 3 years update / support as per tss no. 12 13 perforated uv stabilized grp / frp cable trays as per tss no. 13 14 grp / frp cable tray wall mounting accessories as per tss no. 14 15 63 mm od plb hdpe conduit as per tss no.15 16 2 inch id double wall corrugated flexible hdpe pipe as per tss no. 16 17 1.67 inch id size double wall corrugated flexible hdpe pipe as per tss no. 17 18 100 mm id gi pipe with coupler as per tss no. 18 19 armoured12 coresingle mode fiber cable as per tss no. 19 20 armoured6 coresingle mode fiber cable as per tss no.20 21 armoured24 coresingle mode fiber cable as per tss no. 21 22 outdoor rated cat 6 cable as per tss no. 22 23 4 core 4 sq. mm multistrand cu armoured power cable as per tss no. 23 24 25 mm gi flexible conduit as per tss no. 24 25 ip 65 junction box with complete accessories as per tss no. 25 26 5 meter hot dip galvanized ms poleas per tss no. 26 27 gi cable route marker as per tss no. 27 28 fully loaded 8 port single mode liu unit as per tss no. 28 29 rack mount 24 port single mode liu unit as per tss no. 29 30 24 u smart ac rack with power strip & mounting arrangements , cable manager, mcb etc. as per tss no. 30 31 cat 6 patch cord 8 meter as per tss no. 31 32 cat 6 patch cord 3 meter as per tss no. 32 33 fiber duplex patch cord single mode lc / lc type 1 meter as per tss no. 33 34 fully loaded indoor power distribution box with 4 pole rccb 100 ma, 4 pole mcb 16 a as per tss no. 34 35 removal of tiles, digging and trench making of 600 mm depthfor conduit laying and restoration of tiles as per tss no. 35 36 cutting / digging of pcc surface upto 300 mm depth for laying hdpe conduits and restoration of pcc as per tss no. 36 37 making of pole foundation as per given drawing and tss no. 37 38 fo core splicing at lius inside pole jb and server room as per tss no. 38 39 road cutting & trench making of 600 mm depth as per site requirementas per tss no. 39 40 maintenance free earting stations as per tss no. 40 41 gi earthing pipe for pole earting as per tss no. 41 42 foundation making and installation of 12 u outdoor rackas per tss no. 42 43 perimeter lighting poles as per tss no. 43 44 led perimeter lighting fixture as per tss no. 44 45 frp box for perimeter lighting as per tss no. 45 46 gi earthing pipe for pole earting as per tss no. 46 47 3.5c x 70 sq.mm. power cableas per tss no. 47 48 4c x 6 sq.mm. cu conductor cableas per tss no. 48 49 3c x 1.5 sq.mm. flexible cable ( trs ) as per tss no. 49 50 making of cable trench in ground as per tss no. 50 51 end termination of 3.5c x 70 sq.mm. al power cable as per tss no. 51 52 end termination 4c x 6 sq.mm. cu conductor cable as per tss no. 52 53 end termination 3c x 1.5 sq.mm. cu conductor flexible cable as per tss no. 53 54 powder coated outdoor power control feeder pillar as per tss no. 54 55 straight jointing of 3.5c x 70 sq.mm. al conductor power cable as per tss no. 55 56 maintenance free earting stations as per tss no. 56 57 25mmx3mm cu strip as per tss no. 57 58 led flood lighting fixture as per tss no. 58 59 cable marker as per tss no. 59 60 hdpe pipe as per tss no. 60 61 hume pipe as per tss no. 61 62 gi pipe as per tss no. 62 63 gi item as per tss no. 63 64 ms fabricated items item as per tss no. 64 65 ms powder coated item as per tss no. 65 66 excavationof soil as per tss no. 66 67 rcc ( reinforced cement concrete ) works as per tss no. 67 68 pcc ( plain cement concrete ) works as per tss no. 68 69 cutting of road / breaking of pcc as per tss no. 69...

Water Resources Department - Maharashtra

38625205 tender for krishna koyna lift irrigation scheme mhaisal lis (jath part) construction of cross regulator ch. 29/300, hume pipe culvert at ch. 36/160, super passage at ch. 45/120 and valve type chembers (14 nos) on jath main canal tal jath dist sangli...

Bharat Petroleum Corporation Limited - Maharashtra

38623481 internal estimate for construction of nro wagheri sales buidling, culvert works and canopy foundation 7006144 bldg rcc hysd steel bars 7006150 bldg masonry brick foundn cm 1:6 7006154 bldg masonry bm in sup str cm 1:6 7006168 bldg plaster in cm 1:4 19mm thick 7006294 door win float glass . 12mm tk 7006296 door win al fram 101x45 60m pow coat 7006302 door win al fram sliding 60m pow coat 7006308 door win gl and fr ful gl pow coat 12tk 7006318 door win panel & fr part gl 60m powcoat 7006341 door win . . floor spring 7006796 exc ord soil upto 1.5 m 7006886 floor tile . non skid 7.5 tk 7006890 floor tile marbo for size 600 x 600mm 7006896 floor using stone granite 18 tk 7006939 foundn . . rubble soling 7006947 foundn . pcc with 20mm metal 1:3:6 7007177 paint ww . spl anti fungal paint 7007321 sanitary . wc pedestal type 7007325 sanitary . wc pvc flushing ci 7007376 sanitary . inspection chamber 450x450 7007428 sanitary . brass stop cock 12mm 7007449 sanitary . sintex tanks 1000 ltrs. capac 7007438 sanitary . brass bib 12mm crown 7006842 filling moorum 10t avail at site 7006304 door win gl and fr louvered 60m pow coat 7007619 water proofing . . brickbat coba 7006885 floor ceramic dado color 200x200 7006908 floor . . 20 to 22 mm chequere 7007336 sanitary . wash basin 550x400 color 7007352 sanitary . sci nahani trap 100mm 7007409 sanitary . gi pipeline 12 mm 7007437 sanitary . float / ball valve 25mm 7007344 sanitary . hd pvc pipe 100mm 7007343 sanitary . hd pvc pipe 75mm 7007411 sanitary . gi pipeline 25mm 7006142 bldg rcc slab rft paid extra 1:1.5:3 7006949 foundn . rcc 1:2:4 mix 7006176 bldg plaster . neeru finish 7007368 sanitary . . septic tank 15 users 7006948 foundn . rcc 1:1.5:3 mix 7007036 pipe . s, f and paint 50 mm dip cap 7007037 pipe . s, f and paint 75mm fill cap 7007369 sanitary . . soak pit 2.5dia 3dee 7007375 sanitary . . septic tank 50 users 7007453 sanitary steel water tank rcc hume pipe 7007575 tank . . s / fms threaded bolts 9024895 granular su base with material of grade 1 ( 75mm to 0.075mm ) having cbr value 30 9005061 rw road . lay macadam+10t roll 7007462 sanitary steel water tank rcc hume pipe tank pipeline works 7006978 pipe . ms seamless 75 under ord soil 7006972 pipe . ms seamless 50 under ord soil 7007025 pipe . supply of flanges 50 nb dia 7007047 pipe . s, f and paint al cap 50mm 7007048 pipe . s, f and paint al cap 75 mm 7007045 pipe . s, f and paint 50 mm ball valve 7007557 tank . addpointmanhole 100dia 7007144 pump . installing 2 px4hmpd 7007146 pump . installing stp 7007317 roof steel . sections 7007546 tank . . s / f graphite asb. ga 7007552 tank . . s / f 50 mm vent hood 7007553 tank . . s / f bolts & nuts 16m...

Water Resources Department - Maharashtra

38606119 krishna koyna lift irrigation project mhaisal lis ( jath part ) construction of cross regulator at ch. 29 / 300 m., hume pipe culvert at ch. 36 / 140 m., super passage at ch. 45 / 120 m. and valve type chambers ( 14 no.s ) on jath main canal, tal jath, dist sangli...

Nagar Panchayat - Maharashtra

38553798 tender for repair of cement concrete drains and dhapa slips, supply and installation of 300, 450, 600, 800mm hume pipes at necessary places as per nagar panchayat requirements...

Rural Development Department - Maharashtra

38496497 supply of various material t for construction of anganwadi building at nimsakhar 1 cement 2 khadi 20 mm 3 khadi 40 mm 4 murum 5 crush sand 6 natural sand 7 bricks 8 concrete mixer 9 water tanker 10 excavation for foundation in earth, soil 11 excavation for foundation in hard murum 12 steel 13 burnt brick masonry 14 filling in plinth and floors 15 internal cement plaster 16 neeru finish to plastered surfaces 17 sand faced plaster externally 18 frame 19 solid core flush door shutter 20 green marble 21 aluminium sliding window 22 kitchen otta 23 stabiliser pipe / p.v.c. soil vent / waste pipe 24 hume pipe septic tank 25 fiber glass reinforced polyster door shutter 26 white glazed earthenware orissa type w.c. pan 27 steel ventilator fully glazed partly fixed 28 h.d.p container syntex or alike one piece moulded water tank 29 cpvc pipe 30 vitrified mat finish tiles 31 two coats ofwater proof cement paint 32 priming coat on cement plastered surface including sacffolding 33 ceramic tiles 34 miled steel work for windows 35 information board 36 royalty charges 37 testing charges 38 gst charges ( on work portion ) 39 inshurance ( on work portion ) 40 labour charges for all work...

Rural Development Department - Maharashtra

38427638 providing and supplying material for civil work at grampanchayat khairgaon 2 sand ( reti ) 3 crush metal ( khadi ) 4 80mm aggregate 5 40mm aggregate 6 20mm aggregate 7 artificial sand 8 matel sheets 8x4 9 coating sheet 10 wash shand 11 pever bolck 12 nehru finish 13 pup 14 4 brick 15 8 brick 16 6 brick 17 tiles 18 colour 19 300mm hume pipe 20 450mm hume pipe 21 600mm hume pipe 22 900mm hume pipe 23 chember frame 24 chember cover 25 g.i. pipe 3 26 g.i. pipe 4 27 nut bolts 28 kota flooring 29 steel pipe 30 steel 31 fly ash block 32 ceramic tiles 33 cement 34 murum 35 mcb 36 pole box 37 6 sq.mm service cable 38 led street light 36w 39 flood light 100w...

Department Of Defence - Maharashtra

38344644 bids are invited for cat b items steel 20 mm dia tata oblique jindal , steel 16 mm dia tata oblique jindal , steel 12 mm dia tata oblique jindal , steel 10 mm dia tata oblique jindal , steel 08 mm dia tata oblique jindal , binding wire gauge size 16 to 20 , timber 2nd class well seasoned hard wood planks plank 12 inch x 1 pt 5 inch x10 inch , lime slacked , pvc pipe 4 inch dia 6 mtr length make ashirvad oblique finolex oblique prince , rcc hume pipe dia 12mm connected with color rcc pipes in 2 pt 5 mtr length class np 2 with sulphate resistance cement suitable for joining with flexible rubber ring , hume pipe 300 mm dia 2m length duly connected with color r c c pipes in class np 2 with sulphate resistance cement suitable for jointing with flexible rubber ring confined gasket joints , inter link chain 4 mm dia mesh size 4 inch , icbp 80 mm conceret block interlocking tiles 6 cm thick of size 0 pt 225 meter x 0 pt 1125 mtr or 0 pt 0253 sqm area per no total quantity : 71351...

Western Coalfields Limited - Maharashtra

38119893 tender for civil work. 1 supplying & placing of empty cement bags filled with sand / ob / available earth at desired / different locations of naigaon deep ocm under neeljay sub area of wani area. 190416.60 2400.00 90 day 2 supplying & placing of empty cement bags filled with sand / ob / available earth at desired / different locations of neeljay deep ocm under neeljay sub area of wani area. 190416.60 2400.00 90 day 3 cleaning of drains & r.c.c hume pipe culverts and making katcha drain in workshop / service building premises at neeljay deep ocm under neeljay sub area. 198144.66 2500.00 90 day 4 making shed for capacitor bank & raising height of 02 nos transformer foundation of 11 kv sub station of neeljay deep ocm mine at neeljay sub area of wani area. 187840.81 2400.00 15 day 5 providing and fixing of mdf panelling to 150 t weigh bridges of neeljay deep ocm under neeljay sub area. 193275.54 2450.00 15 day 6 c.g.i sheet roofing of auto electric section of naigaon ocm under neeljay sub area. 42627.16 600.00 04 day...

Western Coalfields Limited - Maharashtra

38042899 different civil works 1 cleaning of culvert and providing ob filled bags at various location at mungoli ocm mungoli sub area 2 cleaning of hume pipe culverts repairing of rain cuts and side berms cleaning etc at kolgaon ocm under mungoli sub area...

Rural Development Department - Maharashtra

37986322 providing and supplying material at gp bharwaj, tal. igatpuri, dist. nasik , providing civil work material , sand ( reti ) , crush metal ( khadi ) , 80mm aggregate , 40mm aggregate , 20mm aggregate , artificial sand , matel sheets 8x4 , coating sheet , wash shand , pever bolck , nehru finish , pup , 4 brick , 8 brick , 6 brick , tiles , colour , 300mm hume pipe , 450mm hume pipe , 600mm hume pipe , 900mm hume pipe , chember frame , chember cover , g.i. pipe 3 , g.i. pipe 4 , nut bolts , kota flooring , steel pipe , steel , fly ash block , ceramic tiles , cement , murum...

Western Coalfields Limited - Maharashtra

37966580 tender for civil works 1. cutting and desilting of drain by side of dump maasala village at docsa. 179632.40 2300.00 7days 2. cleaning inlet & outlet of hume pipe at various places at docsa. 155898.95 2000.00 7days...

Western Coalfields Limited - Maharashtra

37926216 cleaning inlet and outlet of hume pipe at various places at docsa. earth work in excavation by mechanical means ( hydraulic excavator ) / manual means in foundation trenches or drains ( not exceeding 1.5 m in width or 10 sqm on plan ) , includingdressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.all kinds of soil....

Military Engineer Services - Maharashtra

37922855 maint and repair to path ,parking ,gates boundary walls ,security perimeter wall drain cover rcc and hume pipe culverts and other misc items at mo (mb) ghatkopar under ge(nw) bhandup...

Reserve Bank Of India - Maharashtra

37872548 gully trap providing and fixing square mouth with 160mm each side s.w gully trap class sp 1 ( p type ) complet ??...as per specification of item no.1 of price bid 2 2 rcc hume pipe 150 mm dia rcc hume pipe??...as per specification of item no.2 ( i ) of price bid 3 3 rcc hume pipe 200 mm dia rcc hume pipe??...as per specification of item no.2 ( ii ) of price bid 4 4 rcc hume pipe 300 mm dia rcc hume pipe??...as per specification of item no.2 ( iii ) of price bid 5 5 rcc hume pipe do as per item.no. 2 ( ii ) but where pipe and fittings of above diameters are supplied by the bank, ??...as per specification of item no.2 ( ii a ) of price bid 6 6 rcc hume pipe do as per item.no. 2 ( iii ) but where pipe and fittings of above diameters are supplied by the bank ??...as per specification of item no.2 ( iii a ) of price bid 7 7 manhole do as per item no. 3 for a manhole of inside dimension 90cm x 80cm and deep 45cm to 90cm ??...as per specification of item no.3 ( i ) of price bid 8 8 manhole do as per item no. 3 for a manhole of inside dimension 90cm x 80cm and deep 90cm to 160cm ??...as per specification of item no.3 ( ii ) of price bid 9 9 manhole extra over item no. 3 ( ii ) for manholes with depth beyond 1.60m ??...as per specification of item no.3 ( iii ) of price bid 10 10 manhole do as per item no. 3 for inspection chambers for storm water of inside dimension 90cm x 80cm and deep 90cm to 160cm.manhole cover shall be hd 20 with approved pattern gratings. ??...as per specification of item no.4 of price bid 11 11 manhole extra over item no. 4 for chambers with depth beyond 1.60m ??...as per specification of item no.4 ( i ) of price bid 12 12 manhole providing and constructing brick masonry circular type manhole 1.22m internal dia at bottom and 0.56 ??...as per specification of item no.5 of price bid 13 13 manhole ( extra over item 5 above for depth beyond 1.68 to 3.00m for circular type manhole 1.22m interna ??...as per specification of item no.5 ( i ) of price bid 14 14 manhole cover supplying and fixing heavy duty ( hd 20 ) precast manhole covers with frame as per is 12592 latest revi ??...as per specification of item no.6 of price bid 15 15 manhole cover do as per item no. 24 for inspection chambers for storm water of inside dimension 90cm x 80cm exce ??...as per specification of item no.6 ( i ) of price bid 16 16 foot rest providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per is:10910 ??...as per specification of item no.7 of price bid 17 17 misc work making connection of drain or sewer line with existing manhole including breaking in and making good ??...as per specification of item no.8 of price bid 18 18 misc work making connection of rain water from the desilting chamber to the existing tank / compartment after pr ??...as per specification of item no.9 of price bid 19 19 desilting chamber constructing desilting chamber of inside size 2000 x 1200 x 1200 mm ( d ) in aac block work of 2 ??...as per specification of item no.10 of price bid 20 20 garden laterals providing and fixing 12mm dia in class 2 polyethylene laterals conforming to is:12786 of approv ??...as per specification of item no.11 of price bid 21 21 garden laterals providing and fixing 16mm dia in class 2 polyethylene laterals conforming to is:12786 of approv ??...as per specification of item no.11 of price bid 22 22 garden sprinklers supplying and installing sprinkler nozzles of hdpe material along with different accessories v ??...as per specification of item no.12 of price bid 23 23 garden hydrant providing and fixing 20mm dia brass garden hydrant with necessary fittings and fixture ??...as per specification of item no.13 of price bid 24 24 cgst enter total cgst 25 25 sgst enter total sgst...

Western Coalfields Limited - Maharashtra

37789827 supplying and laying sand ob earth filled cement bags cleaning of hume pipes replacement of damaged gi sheet and other misc. works regarding monsoon at pouni ii expansion ocm under pouni sub area....

Western Coalfields Limited - Maharashtra

37789819 supplying and laying sand ob earth filled cement bags cleaning of hume pipes and other misc. civil works by manual means at gouri deep ocm under gouri sub area....

Western Railway - Maharashtra

37763512 tender for vr jrs section: providing additional water way at various locations for prevention of flooding of tracks during monsoon by laying 1800mm dia rcc hume pipe by micro tunnelling...

Rural Development Department - Maharashtra

37745377 providing and supplying material for civil work at grampanchayat khairgaon supplying of material at gram panchayat khairgaon tal igatpuri dist nasik , providing civil work material , sand (reti) , crush metal (khadi) , 80mm aggregate , 40mm aggregate , 20mm aggregate , artificial sand , matel sheets 8x4 , coating sheet , wash shand , pever bolck , nehru finish , pup , 4 brick , 8 brick , 6 brick , tiles , colour , 300mm hume pipe , 450mm hume pipe , 600mm hume pipe , 900mm hume pipe , chember frame , chember cover , g.i. pipe 3 , g.i. pipe 4 , nut bolts , kota flooring , steel pipe , steel , fly ash block , ceramic tiles , cement , murum...

Military Engineer Services - Maharashtra

37740133 provn of toilets for sncos mess and certain other otm areas, provn of valley gutter at officers mess, installation / fitment of acp in front of annexe hall and hume pipe culvert in front of bldg no. p 234, at vayusena nagar nagpur...

Rural Development Department - Maharashtra

37668842 providing and supplying material for civil work at grampanchayat pimpri sado supplying of material at gram panchayat pimpri sado tal nashik dist nasik , providing civil work material , sand ( reti ) , crush metal ( khadi ) , 80mm aggregate , 40mm aggregate , 20mm aggregate , artificial sand , matel sheets 8x4 , coating sheet , wash shand , pever bolck , nehru finish , pup , 4 brick , 8 brick , 6 brick , tiles , colour , 300mm hume pipe , 450mm hume pipe , 600mm hume pipe , 900mm hume pipe , chamber frame , chember cover , g.i. pipe 3 , g.i. pipe 4 , nut bolts , kota flooring , steel pipe , steel , fly ash block , ceramic tiles , cement , murum...

Moil Limited - Maharashtra

37651416 laying hume pipe for sewer line providing and laying rcc hume pipe sever line from new a type quarters colony up to stp at gumgaon mine => limited...

Water Resources Department - Maharashtra

37595943 construction of pipe vrb to side drain @ rd 1450 m & 1650 m banking portion & construction of pipe vrb to ip side on side drain @ rd 4830 m & 4840 m on wadadh distributory, construction of drop hume pipe clvert @ rd 1530 of sirasagaon tail minor of wadadh distributory...

Western Coalfields Limited - Maharashtra

37515097 civil works 03 misc civil works at kolarpimpri pimpalgaon sub area of wani north area. 1 painting of boards, slogans writing and area cleaning in mine premises of pimpalgaon opencast mine under kolarpimpripimpalgaon sub area of wani north area. pimpalgaon opencast mine. rs. 1, 96, 320.14 rs. 2500 / 30 days 2 laying of rcc hume pipes at various crossings during monsoon 2023 2024 at pimpalgaon opencast mine under kolarpimpri pimpalgaon sub area of wani north area. pimpalgaon opencast mine. rs. 79, 607.43 rs. 1000 / 30 days 3 laying of rcc hume pipes at various crossings during monsoon 2023 2024 at kolarpimpri opencast mine under kolarpimpri pimpalgaon sub area of wani north area. kpoc mine premises. rs. 1, 96, 604.24 rs. 2500 / 90 days...