39865949
bids are invited for hands file for second cut flat , car jet washer with standard accessories , chain pulley block capacity with tripod stand 3 ton , compression testing gauge suitable for diesel engine with standard accessories , cylinder bore gauge capacity 18 to 35 mm , cylinder bore gauge capacity 35 to 60 mm , cylinder bore gauge capacity 50 to 150 mm , cylinder liner dry and wet liner, press fit and slidefit liner , different type of engine bearing model , different type of piston model , fuel feed pump for diesel , gloves for weldingleather and asbestos , injector cleaning unit , injector testing set hand tester , oil pump for dismantling and assembling. , oil stone 15 cm x 5 cm x 2.5 cm , oscilloscope 20mhz , tinnmans shear450 mm x 600mm , sheet metal gauge , tinnmansshear 300mm , soldering copper hatchet type 500gms , spanner clyburn 15 cm , spanner d.e. set of 12 pieces 6mm to 32mm , spanner t. flocks for screwing up and up screwing inaccessible , spanner adjustable 15 cm , spanner, ring set of 12 metric sizes 6 to 32 mm , spanners socket with speed handle, t bar, ratchet and universal , spark lighter , spark plug spanner 14mm x 18mm x size , starter motor axial type, pre engagement type and co axial type , steel measuring tape in a case 10 meter , steel rule 15 cm inch and metric , steel rule 30 cm inch and metric , straight edge gauge 2 ft. , straight edge gauge 4 ft. , stud extractor set of 3 , stud remover with socket handle , surface gauge with dial test indicator plunger type 0.01 mm , tachometer counting type , tandem master cylinder with booster , taps and dies complete sets 5 types , taps and wrenches metric , telescope gauge , temperature gauge with sensor 0 100 0c , thermostat , thread pitch gauge metric , timing lighter , torque wrenches 5 35 nm, 12 68 nm and 50 225 nm , trammel 30 cm , turbocharger cut nm and 50 225 nm , trammel 30 cm , turbocharger cut sectional view , tyre pressure gauge with holding nipple , universal puller for removing pulleys, bearings , vacuum gauge 0 to 760 mm of hg. , valve lifter , valve spring compressor universal , vice grip pliers , water pump for dismantling and assembling , arbor press hand operated 2 ton capacity , rule steel 300 mm both in inch and mm , hacksaw frame adjustable 250 to 300 mm , scriber 200 mm , centre punch 100 mm , chisel cold, flat 20 mm , hammer ball peen 800 grams , file flat rough 300 mm , level spirit wooden 300 mm , plumb bob 50 grams , trowel c 125 i s 6013 , stillson wrench 300 mm , screw driver 200 mm , screw driver 400 mm , cutting pliers 200mm i s 3650 , steel tape 5m , hand vice, jaw 50 mm , file flat, smooth 200 mm , file half round, bastard 250 mm , file, square, bastard 300 mm , file, square, smooth 200 mm , file triangular bastard 300 mm , file flat rasp 250 mm , file triangular smooth 200 mm , chisel cold flat 32 mmx300mm , chisel cross cut 6x150 mm i s 402 , chisel round nose 3x150 mm i s 402 , chisel diamond point 6x150mm , punch, letter set 6mm , punch , number set 6mm , spanner monkey up to 50mm , cutter, pipe, wheel type 6mm to 25mm , oil stone 150x50x25mm , soldering iron, copper, bit, fire heated, hatched, straight 500 grams , try square 200mm , inside caliper , caliper outside 150mm , odd leg caliper 200mm , d. e. spanners 6x7, 8x9, 10x11, 12x13, 16x17, 18x19, 20x22, 24x27. , bending spring , tool caulking , plumbers metal melting pot , pipe stock and dies complete with stocks, bushing, bushing holders, half to 2inch bsp , pipe vice to grip up to 75 mm is 2587 , stillson pattern pipe wrenches 450 mm , stillson pattern pipe wrenches 300mm to take pipe 20 mm to 32mm , chain pipe wrench , adjustable, spanner, a 375, is 6149 90mm 650 is 4123 , leg vice, 75mm jaw on stand is 2588 , hand drill 6mm capacity with drill chuck electric , drill twist straight shank 3mm to 6mm , wash basin equivalent metric 16inchx14inchx10inch , water heater 10 litres , water closet european type p complete with overhead cistern , water closet indian type complete with overhead cistern , water meter , rachet pipe die 15 mm to 25 mm , rachet pipe die 30 mm to 50 mm , double face hammers , cpvc orupvc pipe cutter std size , hard disk drives ( q2 ) total quantity : 589...
Due Date : October 06, 2023
Tender Value : ₹ Ref. Documents